Community Research and Development Information Service - CORDIS

Horizon 2020 project information and now also report summaries are available on CORDIS. All H2020 projects can be downloaded from the EU Open Data Portal .

My refinements


Download results of this page


Refine by:

Content type

Project (83)

Country

Belgium (7)
France (7)
Germany (27)
Italy (15)
Luxembourg (4)
Netherlands (7)
United Kingdom (13)

Advanced search

Search projects and results

Results 1 - 10 of 83
Results/page:
12 3 4 5 6 7 8 9 > 
ID: 7210-SA/203
Start date: 1985-10-01, End date: 1987-10-31
Architects, no-professional decision makers and investors need guidelines covering the major aspects of fire safety, especially for steel constructions, which are explained and accessible. For this audience, available literature is not easy to understand and does not provide a...
Programme: ECSC-STEELRES 6C
Record Number: 14221
Last updated on: 2002-12-13
ID: 7210-KA/313
Start date: 1985-07-01, End date: 1988-06-30
MOTOR-VEHICLE MANUFACTURE AND THE PREFABRICATION OF LIGHT-METAL STRUCTURAL COMPONENTS ARE CURRENTLY AREAS WHERE THE SPOT-WELDING ASSEMBLY TECHNIQUE IS IN USE. THE WORK PROPOSED - WHICH TAKES ACCOUNT OF PREVIOUS WORK - IS INTENDED EXPERIMENTALLY TO DETERMINE RESIDUAL STRESS...
Programme: ECSC-STEELRES 6C
Record Number: 14214
Last updated on: 1989-11-24
ID: 7210-EB/401
Start date: 1985-07-01, End date: 1988-12-31
THE VARIOUS TYPES OF CARBON-STEEL WIRE ROD NOW ON THE MARKET CAN BE DIVIDED INTO TWO MAIN CATEGORIES ACCORDING TO USE : (A) MEDIUM- AND HIGH-CARBON WIRE ROD FOR CABLES, SPRINGS, TYRE PLIES, ETC.; (B) MEDIUM- TO LOW-CARBON WIRE ROD FOR NUTS AND BOLTS, BEARINGS, SOLDERING W...
Programme: ECSC-STEELRES 6C
Record Number: 13886
Last updated on: 1989-11-24
ID: 7210-KA/810
Start date: 1985-10-01, End date: 1988-03-31
RESISTANCE SPOT WELDING IS ONE OF THE MOST WIDELY EMPLOYED PROCESSES IN THE MASS PRODUCTION INDUSTRIES FOR THE JOINING OF THIN SHEET. IN SPITE OF THIS THERE IS LIMITED STANDARDIZATION REGARDING QUALITY CONTROL PROCEDURES, ASSESSMENT OF WELD QUALITY AND MEASUREMENT OF WELDING P...
Programme: ECSC-STEELRES 6C
Record Number: 14211
Last updated on: 1994-01-23
ID: 7210-GF/306
Start date: 1985-07-01, End date: 1988-06-30
THE EMERGENCE OF ARRAYS OF X-RAY-SENSITIVE PHOTOSENSORS IS MAKING IT POSSIBLE TO DESIGN A NEW GENERATION OF GAUGES FOR MEASURING THE THICKNESS PROFILE OF HOT-AND COLD-ROLLED STRIP. IN COMPARISON WITH CURRENT PRACTICE - IN WHICH AT BEST THE RADIATION SOURCE, OR AT WORST THE SO...
Programme: ECSC-STEELRES 6C
Record Number: 14217
Last updated on: 1994-01-23
ID: 7210-GF/602
Start date: 1985-07-01, End date: 1989-06-30
STUDY AND RESEARCH AIMED AT DEVELOPING VALID SELECTION CRITERIA FOR THE ACQUISITION OR CONSTRUCTION OF DATA RECORDING AND PROCESSING EQUIPMENT. THIS RESEARCH WILL BE SO CONDUCTED AS TO LEAD TO A STANDARD FORMULATION OF DEFINITIONS FOR THE CHARACTERIZATION OF MATERIALS USED IN ...
Programme: ECSC-STEELRES 6C
Record Number: 14219
Last updated on: 1994-01-23
ID: 7210-GB/103
Start date: 1984-07-01, End date: 1988-06-30
THIS PROJECT IS A FOLLOW-UP TO TWO EARLIER CONTRACTS (7210.GA/120 AND 7210.GA/810) IN THE SAME FIELD. THE AIM IS TO DEVELOP A MEASURING METHOD TO DETERMINE INTERNAL MECHANICAL STRESSES IN ROLLED AND FORGED PRODUCTS. INTERNAL STRESSES, WHICH WILL BE ANALYSED SOLELY BY AN ULTRA...
Programme: ECSC-STEELRES 6C
Record Number: 13883
Last updated on: 1994-01-23
ID: 7210-AA/209
Start date: 1985-10-01, End date: 1989-09-30
ALL BLAST-FURNACE OPERATORS AGREE THAT THE COHESIVE ZONE IS CRITICAL IN THE PERFORMANCE OF A BLAST FURNACE. THE AIM OF THIS RESEARCH IS TO SEEK WAYS AND MEANS OF OPTIMIZING THE SHAPE AND POSITION OF THE COHESIVE ZONE.
Programme: ECSC-STEELRES 6C
Record Number: 13920
Last updated on: 1994-01-23
ID: 7210-EA/212
Start date: 1985-07-01, End date: 1988-06-30
THE AIM OF THE RESEARCH IS TO IMPROVE THE DIMENSIONAL QUALITY OF THE BUTT-ENDS OF STRIP PRODUCED IN CONTINUOUS HOT-ROLLING MILLS.
Programme: ECSC-STEELRES 6C
Record Number: 13893
Last updated on: 1994-01-23
ID: 7210-EA/505
Start date: 1983-07-01, End date: 1988-06-30
UNLIKE MILLS FOR FLAT PRODUCTS, BEAM MILLS ARE NOT GENERALLY EQUIPPED WITH ADVANCED TECHNICAL SYSTEMS FOR CONTROLLING THE ROLLING PROCESS. IN THEIR ABSENCE, IT IS DIFFICULT TO ADJUST THE MILL PARAMETERS (ROLLING PLAN, ROLL POSITIONING, ETC.) TO THE VARIATIONS IN ROLLING CON...
Programme: ECSC-STEELRES 6C
Record Number: 13891
Last updated on: 1989-11-24
12 3 4 5 6 7 8 9 > 
List retrieved on: 2017-10-24
Follow us on: RSS Facebook Twitter YouTube Managed by the EU Publications Office Top