Service Communautaire d'Information sur la Recherche et le Développement - CORDIS

FP6

ALAMO Résumé de rapport

Project ID: 512833
Financé au titre de: FP6-SME
Pays: United Kingdom

Final Report Summary - ALAMO (Development of innovative high performance anodised aluminium moulding tools for the thermoplastic processing sector to achieve competitive advantage)

The use of aluminium tooling for the processing of plastics is widespread within the European Union as it has some very desirable characteristics such as high thermal conductivity, low weight and quick machinability. Its expansion is limited however by its relatively poor wear, abrasion and chemical corrosion resistance. It is used commonly for low volume or prototype manufacture in high and low pressure processes.

The anodising process developed in the project ALAMO overcomes these shortcomings to achieve anodised aluminium tools which con compete with steel stools in the injection, blow and rotational moulding sectors.

The project started in November 2004, and the main objectives were to produce tooling with:
- high wear resistance;
- good thermal conductivity;
- good corrosion resistance.

In addition, the tools would be lighter and quicker to manufacture than steel and also less expensive. The quicker production moulding cycle times achieved would also reduce component manufacturing costs and result in greater competitiveness in the global market by way of licensed technology.

Two processes, injection moulding and rotational moulding were selected for trials and two corresponding state-of-the-art aluminium alloys were chosen to make anodised tools from. AW 7010 was chosen for injection moulding - a state of the art 'hard' alloy material introduced recently to replace AW 7075 and AW 6082 for rotational moulding - a 'soft' alloy with excellent corrosion resistance and lower cost (50 % cheaper) than AW 7010/7075.

The two streams of investigation would produce a 'high emissivity' formulation for rotational (and blow) moulding, where pressures ore low and efficient cooling/heating is essential to slash long cycle times and a 'high wear 'formulation for injection mould tools, that can withstand high injection pressure and clomping forces.

A design of experiment process was followed to create a series of test plaques which defined then optimum parameters to achieve the desired properties such as hardness, wear resistance, emissivity, thermal conductivity and compressive resistance. The results were promising and the project progressed to the stage of making test tools in order to trial on a small scale the effect of anodising aluminium surfaces.

For the injection moulding tests o tour-impression test tool was manufactured which tested steel and aluminium substrates, anodised and un-anodised. The port manufactured was designed to create high wear areas by means of narrowing cavities and sharp corners.

Running concurrently with the tool manufacture a CAD simulation was created to investigate the theoretical differences that anodising would make to filling, temperature, velocity, and pressure and so on. The results for the test tool showed good commonality between the actual and theoretical data.

For the rotational moulding test, two 300 mm cube tools were manufactured, one anodised and one in natural aluminium. Comparative tests were run and various parameters were measured, internal and external to the tool. It could be clearly seen that there was a substantial reduction in cycle time between anodised and non-anodised tools and this was later quantified as a 15 to 20 % reduction in cycle time from treated to non treated aluminium.

Because of the reduction in cycle time there is also a commensurate reduction in gas and electricity usage. The energy used to anodise on average tool is saved in approximately seven mouldings. The calculation is by no means a life cycle analysis but it shows the order of energy saving for rotational mould tools is extremely worthwhile.

For both injection and rotational trials the resultant mouldings were subjected to on array of tests such as GPC, colour, gloss, density and DSC in order to discover whether the improved processing efficiency had affected the properties of the mouldings. No changes were detected which was positive, showing that tool performance hadn't been gained ot the expense of material properties.

The test tools were highly successful and showed the impressive potential of anodised tools and so the next stage was embarked upon which was to make industrial tools more akin to real life situations.

For the injection tool an ambitious and quite complicated ton moulding tool was manufactured in anodised aluminium, replicating an existing steel tool. The exercise proved invaluable in learning about the details of how anodising affects the process of high precision tool making, how the tolerances are affected, the provision for standard inserts and tool matching. This particular tool showed that although the anodising is only 30 microns thick it affects the fit of tooling components and provision needs to be mode at the machining stage or the anodising stage for this, and techniques were proposed and trialled.

The anodising was successful in the aspects of appearance, wear and hardness. Much was also learned about the specification and finishing of tools with regards to anodising and a simple solution was proposed for future use by the anodising companies (involving controlled etching of the tool). The complexity of the tool did not cause problems for the anodising process but it the moulding trials were curtailed as the release of ports from the tool was difficult. The anodised surface may have had no influence on this problem but in the course of releasing the ports from the tool the formic acid used to dissolve the polymer over many days also damaged the anodised surface ending the trials in the time available.

At the final meeting of the consortium it was agreed that the use of anodised aluminium tooling should be considered, as any other parameter, on a job by job basis, taking into account port geometry, surface area to thickness ratio, size, draw angles, surface finish, moving parts, and ejection and so on. The software, tooling and moulding experience gained in ALAMO will help this decision.

The industrial tool for the anodising process was based on the test tool but with the addition of MECH (ceramic electrical heating panels), the latest innovation for roto-moulding tools, it was evident, as expected, that the cycle time benefits experienced in the industry standard oven-heating manufacturing method did not apply to the contact-heating method but the hardness, wear and corrosion resistance were beneficial.

Again, samples of mouldings were taken from the industrial trials, tested in detail, and showed no discernable differences between non-anodised and anodised tooling production showing that the benefits accrued have not been at the expense of material properties.

The ALAMO project has proved the viability of the combined technologies of aluminium tooling and anodised surfaces and the further development of the techniques will lead to many new applications.

Informations connexes

Reported by

RAPRA TECHNOLOGY LTD.
SY4 4NR SHREWSBURY
United Kingdom
See on map