Servicio de Información Comunitario sobre Investigación y Desarrollo - CORDIS

FP6

CELINA Informe resumido

Project ID: 516126
Financiado con arreglo a: FP6-AEROSPACE
País: Germany

Final Report Summary - CELINA (Fuel cell application in a new configured aircraft)

The 'Fuel cell application in a new configured aircraft' (CELINA) project started out to investigate the operational behaviour of the complete fuel cell system including kerosene reformer, fuel cell stack, air supply and all subsystems based on simulation models and tests. In view of the aircraft's operational conditions, the electrical load conditions, the thermal management, the mass flow and the performance of fuel cell system are investigated. Relevant safety and certification requirements have been developed including a preliminary safety assessment for on-board application.

Fuel cell systems allow converting a variety of fuels used in aviation such as hydrogen, natural gas or Jet A fuel into electrical power. This makes them cleaner and quieter than most other power supplies. Fuel cell systems are an ideal alternative for conventional on-board power sources used in airplanes such as auxiliary power units or ram air turbines. In fact, they are considered as ideal power source for the all-electric aircraft of the future. However, before fuel cell systems can be installed into aircraft, a number of technological challenges remain to be solved.

Early in the project it became obvious that commercially available fuel cell system components are not suitable for aircraft application because e.g. of their present power-to-weight ratio. This finding required CELINA to place an extra effort into changing of objectives regarding to installation concept definition.

CELINA demonstrated that fuel cell systems are suitable for airborne use if properly integrated into the aircraft's electrical network and if safety and cooling aspects as well as the power management are organised appropriately.

The investigation of the fuel processing showed that kerosene reforming onboard aircraft is a long-term research topic. Today, all known reformer projects in Europe are running only on laboratory level requiring a significant financial investment and time for reaching airworthiness levels.

Similarly, Solid oxide fuel cells (SOFC) are at present operated only on laboratory level. Application to flight conditions requires huge investments and technical solutions for safely managing the up to 800 degrees Celsius of operating temperature onboard of an aircraft.

Originally, a 50 kWel system architecture as replacement for the ram air turbine was designed and simulated as intermediate step for 500 kWel system as future auxiliary power unit replacement.

However, it became obvious that in the near to mid-term such complex fuel cell system architecture would not be suitable as standard design and that based on state-of-the-art technology it would be far beyond what is acceptable in commercial aircraft.

The major obstacles are the high specific system weight, the high space requirements of cooling equipment and the complex fuel processing technology. As a consequence, pure hydrogen might be the preferred fuel for the first commercial in-flight application of fuel cells.

In order to optimise the system efficiency all by-products as heat, water and inert gas need to be utilised aboard an aircraft allowing the fuel cell system to take over additional services on ground and during flight in addition to ram air turbine and auxiliary power unit replacement.

Influences of type of fuel processing, fuel cell technology and flight mode on the fuel cell system efficiency have been analysed within CELINA. The figure below shows the development targets for the efficiency of polymer electrolyte fuel cells in order to meet aircraft requirements.

The consortium faced many challenges and finally had to re-adjust several objectives with respect to the application readiness of fuel cell systems. But many lessons have been learned. The difficulties have been in definition of consistent interfaces between the corresponding modules between different partners while on the other hand the fuel cell system models were modelled partly too detailed.

In general, the original envisaged improvements were validated with the potential benefits which are depending on the respective type of aircraft.

Future fuel cell research for flight applications should consider the following recommendations:
- Main off-the-shelf fuel cell system components need to be modified and re-designed for aircraft application
- In order to reach maximum efficiency all by-products (heat, water, exhaust gas) have to be utilised aboard the aircraft allowing the fuel cell system to take over additional services on ground and during flight in addition to ram air turbine and auxiliary power unit replacement.
- The power-to-weight ratio and the structural volume of present fuel cell systems need to drop below today's standards given by conventional auxiliary power units and ram air turbines.
- The reliability and durability of system components under all flight conditions including vibrations over long operating live times need to be investigated with respective aircraft requirements to be specified.
- Redundant fuel cell system architectures have to be developed to guaranty reliable and safe operation in major failure scenarios.
- To improve the long-term performance of the SOFC running on commercial hydrocarbon fuels, research should address the development of kerosene/diesel reformer and the development of advanced sulphur and carbon tolerant anode materials with superior catalytic and electrical properties.

Información relacionada

Contacto

Christine SCHILO, (Project Manager)
Tel.: +49-40-743-81850
Fax: +49-40-743-74727
Correo electrónico
Síganos en: RSS Facebook Twitter YouTube Gestionado por la Oficina de Publicaciones de la UE Arriba