Skip to main content
European Commission logo
English English
CORDIS - EU research results
CORDIS
CORDIS Web 30th anniversary CORDIS Web 30th anniversary

Article Category

Content archived on 2023-03-01

Article available in the following languages:

EN

Nanofabrication: next generation chip manufacture?

A new nanotechnology tool that will dramatically cut the cost of leading-edge nano research at the sub-50nm scale has been developed by EU researchers. It could lead to Next Generation Lithography (NGL) technology.

The commercially available first generation tool is low cost compared to sub-50nm alternatives. For example, electron beam lithography costs 2m per machine, whereas the Soft Ultraviolet (UV) Imprint machine developed by SOUVENIR project costs in its basic version well below 200,000. It will be used to produce novel and experimental nanotech devices. "In principle, this new technique has the potential to be used for mass manufacture by the semiconductor industry. One approach we use can already form patterns down to the 10nm scale," says Dr Markus Bender, researcher at German company, Applied Micro- and Optoelectronics (AMO), and SOUVENIR coordinator. Next Generation Lithography (NGL) is the holy grail of the semiconductor industry. It will allow rapid, large-scale manufacture of modern microchips at a sub-50nm scale. Industry giant Intel has spent 15 years and millions of dollars looking for it. A small but brilliant team of dedicated researchers in Europe may have found the solution. Photolithography works by casting light through a mask to produce a pattern on a chemically-coated substrate. The light changes the chemical structure of the substrate. Depending on the type of photolithography, either the lit or shadowed chemical is washed away in the next step. In either case the result is a pattern etched into the substrate. With nanolithography the patterns are invisible to the naked eye and the vast majority of the world's microscopes. The result is the tiny circuits in semiconductor chips. The SOUVENIR project developed a new technique to create those patterns, one that is low cost and, comparatively, low tech. In a first step the substrate was coated with a low viscosity, UV-curable resist. The resist is simply a UV-sensitive chemical layered onto the substrate. They then used a soft polymer mould, called an elastomer, pressed against the resist-coated substrate, called imprinting, followed by the UV photopolymerisation, or curing, of the resist. This costs less than other photolithographic techniques. Because the mould is pressed against the resist, the system does not require the extremely expensive 'deep' UV light sources used in the semiconductor industry. These light sources can only work properly in a vacuum. Finally, the elastomer mould is considerably cheaper than those used in microchip manufacture. The result is a low-cost pattern process at the sub-50nm scale. However, the low cost comes at a price. Currently, the system is too slow and unproven to replace the current industrial photolithography processes. What's more, the elastomer moulds used in the SOUVENIR process at the moment need further improvements for high-resolution alignment processes, essential for mass manufacturing semiconductors. But ultimately it has the potential to become the next generation lithography. Thanks to research completed by the German government's Federal Ministry of Education and Research (BMBF), it is possible to use the same imprinting technique using a hard mould, based on quartz, which does have the required precision for semiconductor manufacture. However, while quartz could address the precision issues the technique is currently too slow for large-scale semiconductor companies. "This is the first generation of the tool we developed and, with work, we can in principle get much better, faster and more scalable results," says Dr Bender. "We are working in close cooperation with an Austrian company, Electronic Vision Group (EVG) to develop tools for the two approaches. I think next year we'll have a step and repeat tool for 300mm wafers on the market," says Dr Bender. This first generation tool is designed for small volume production, for example for chemical sensors and in biotechnology applications at small companies and research centres. Right now, small companies can't afford their own tools for sub-50nm nanotech devices. But ultimately, this research could change how the semiconductor industry works. "This is a totally new technique and we've got to prove that we can reliably reproduce the results. That's what we'll be doing now," says Dr Bender. Contact: ,Dr Markus Bender,AMO GmbH,D-52074 Aachen ,Germany,Tel: +49-241-8867203,Email: bender@amo.de ,http://www.soft-uv-nanoimprint.com/Published by the IST Results service which brings you online ICT news and analysis on the emerging results from the European Commission's Information Society Technologies research initiative. The service reports on prototype products and services ready for commercialisation as well as work in progress and interim results with significant potential for exploitation

Countries

Germany