Deliverables
Report on NEOHIRE dissemination material and publications
Comparisson between LCA&LCC for NdFeB Permanent Magnet manufacturing processes
NEOHIRE projec summary
Descrption of the NEOHIRE dissemination material and publications
Comparison between LCA&LCC & Social LCA regarding NdFeB material solutions
Final report on comparative LCA&LCC for NdFeB Permanent Magnet manufacturing processes Task 5.2 has been extended because of the delay in the definition of the heat treatments to develop the gas atomized powder in WP1. This report will complete the data of D5.4 regarding the comparison between LCA&LCC for NdFeB Permanent Magnet manufacturing processes after process definition at lab scale in WP2.
Comparison between LCA&LCC for NdFeB PM recycling processes
Final NEOHIRE project summary
Final report on comparative LCA&LCC & Social LCA regarding NdFeB material solutions Task 5.1 has been extended because of the delay in the definition of the heat treatments to develop the gas atomized powder in WP1. This report will complete the data of D5.3 regarding the comparison between LCA&LCC & Social LCA regarding NdFeB material solutions.after process definition at lab scale in WP2.
"Comparative ""cradle-to-grave"" LCA&LCC, including the relevant differences within the PM Generator production and use phase."
MODA
Descrption of the NEOHIRE dissemination material and publications
Final samples from both powder sources (fresh and recycling) by both injection and compression moulding technologies at lab scale. Since powders from WP1 and WP4 were not available, preliminary samples produced until month 24 were manufactured using equivalent commercial powders (AICHI HDDR irregular powder and spherical isotropic MQP-S-11-9 powder from MAGNEQUENCH). This was useful to determine the injection and compression moulding parameter. The extension of the Task 2.1 is requested to manufacture the final samples using the powders developed in NEOHIRE
Samples from both powder sources (fresh and recycling) by both injection and compression moulding technologies at lab scale
This is a report containing the results of the validation tests
Final event for the closure of NEOHIRE project
Process flow sheet for the production of Nd2O3 (99.9% purity) from end-of-life NdFeB magnets
Description of the intermediate process flow sheet for the production of Nd2O3 (99.9% purity) from end-of-life NdFeB magnets
Description of the final process flow sheet for the recovery of REEs & Co from bonded PM and of REEs from sintered PM
Anisotropic resin bonded NdFeB magnets from sintered NdFeB magnets (M32-UOB) This deliverable will include report on optimised HDDR conditions for processing of sintered NdFeB magnets into an anisotropic NdFeB powder and also the production of physical samples for their interaction in WP2 of resin-bonded PM obtained from sintered PM wastes
Searching for OpenAIRE data...
Publications
Author(s): G. Sarriegui, J. M. Martin, M. Ipatov, A. P. Zhukov, J. Gonzalez
Published in: IEEE Transactions on Magnetics, 2018, Page(s) 1-5, ISSN 0018-9464
Publisher: Institute of Electrical and Electronics Engineers
DOI: 10.1109/TMAG.2018.2839906
Author(s): Steff Van Loy, Mehmet Ali Recai Önal, Koen Binnemans, Tom Van Gerven
Published in: Hydrometallurgy, 191, 2020, Page(s) 105154, ISSN 0304-386X
Publisher: Elsevier BV
DOI: 10.1016/j.hydromet.2019.105154
Author(s): Mehmet Ali Recai Önal, Sofía Riaño, Koen Binnemans
Published in: Hydrometallurgy, 191, 2020, Page(s) 105213, ISSN 0304-386X
Publisher: Elsevier BV
DOI: 10.1016/j.hydromet.2019.105213
Author(s): Sofía Riaño, Simona Sobekova Foltova, Koen Binnemans
Published in: RSC Advances, 10/1, 2020, Page(s) 307-316, ISSN 2046-2069
Publisher: Royal Society of Chemistry
DOI: 10.1039/c9ra08996a
Author(s): Lorenzo Berzi, Caterina Antonia Dattilo, Francesco Del Pero, Massimo Delogu, Manuel Ignacio Gonzalez
Published in: Procedia Structural Integrity, 24, 2019, Page(s) 961-977, ISSN 2452-3216
Publisher: Procedia Structural Integrity, vol. 24, 2019, p. 961-977
DOI: 10.1016/j.prostr.2020.02.084