Objetivo
The future European emission standards (EURO IV and EURO V) for HD diesel engines demand new truck engine technologies such as an exhaust gas recirculation (EGR), variable nozzle turbocharger (VNT) and exhaust gas after treatment systems. EGR and VNT do influence one another via the exhaust flow and exhaust backpressure. Therefore, within transient operation, a high precision control of EGR and VNT is required to avoid smoke and/or NOx emission peaks. The objective of the proposed project is a research program focusing on a new Advanced Truck Engine Control System ATECS including new strategies for engine control and ECU (electronic control unit) calibration as well as an uncoupling control strategy for EGR and VNT. To achieve this, two European truck engine manufacturers, two suppliers, four university institutes and one combustion engine development company, as co-ordinator will co-operate close together. The expected results are advanced truck engine control strategies for reduced engine out-emissions and improved fuel consumptions as well as an improved dynamic engine response and a reduced transient truck engine application effort.
The objective of the ATECS project is a new Advanced Truck Engine Control System to reduce application effort and improve engine control within transient operation. Starting from the base of a state-of-the-art EURO 3 HD Diesel engine concept the potential of combined EGR and VNT-Turbocharger system application is investigated with focus on EURO 4 and 5 exhaust emission requirements. Special effort will be laid on the investigation of a simulation model for improved engine ECU (Electronic Control Unit) calibration under transient conditions including control algorithms for uncoupling control of EGR and VNT-turbocharger. A controller for uncoupled control of EGR and VGT was researched and tested for Heavy Duty Application. One important part was the generation of a time based non-linear model as development platform for this advanced controller. The non-linear model is programmed in Matlab/Simulink and consists on physically based formulas, which means the usage of maps or neural networks was avoided. By this, real time models are available which later can be implemented in the engine control unit and can be parameterised faster than maps calibrated.
The parameterisation of the model was done by taking engine mappings and turbocharger measurements and optimising the parameters with the least square method. The resulting overall model accuracy is within the range +/-5%, which is sufficient for controller design. Important for controller testing was to achieve a realistic dynamic of the system. Therefore not dynamically measurable values, like the exhaust temperature, were determined by process simulation. By this a reasonable transient model tuning was possible. The structure programmed in Simulink was then implemented in the ECUs of a 1L/Cyl. and a 2L/Cyl. engine. For the 1L/Cyl. engine the controller code was implemented in ASCET and for the 2L/Cyl. engine via target link directly implemented in the ECU code. On the test cell it could be shown, that the uncoupling of VGT and EGR is very effectively possible with the model based predictive controller. This was shown for a 1L/Cyl. engine with the control values air mass and boost, and for a 2L/Cyl. engine with the control values EGR mass and boost. The impact of the uncoupled control on emissions was investigated at load steps and within the ETC. It could be shown that under transient test conditions nearly the same NOx and PM emissions can be realised as they are measured under steady state conditions, this means the normally offset between transient and steady state emissions are negligible using the uncoupled control.
Ámbito científico (EuroSciVoc)
CORDIS clasifica los proyectos con EuroSciVoc, una taxonomía plurilingüe de ámbitos científicos, mediante un proceso semiautomático basado en técnicas de procesamiento del lenguaje natural. Véas: El vocabulario científico europeo..
CORDIS clasifica los proyectos con EuroSciVoc, una taxonomía plurilingüe de ámbitos científicos, mediante un proceso semiautomático basado en técnicas de procesamiento del lenguaje natural. Véas: El vocabulario científico europeo..
- ingeniería y tecnología ingeniería eléctrica, ingeniería electrónica, ingeniería de la información ingeniería electrónica sistemas de automatización y control
- ingeniería y tecnología ingeniería ambiental energía y combustibles
- ciencias naturales informática y ciencias de la información inteligencia artificial inteligencia computacional
Para utilizar esta función, debe iniciar sesión o registrarse
Programa(s)
Programas de financiación plurianuales que definen las prioridades de la UE en materia de investigación e innovación.
Programas de financiación plurianuales que definen las prioridades de la UE en materia de investigación e innovación.
Tema(s)
Las convocatorias de propuestas se dividen en temas. Un tema define una materia o área específica para la que los solicitantes pueden presentar propuestas. La descripción de un tema comprende su alcance específico y la repercusión prevista del proyecto financiado.
Las convocatorias de propuestas se dividen en temas. Un tema define una materia o área específica para la que los solicitantes pueden presentar propuestas. La descripción de un tema comprende su alcance específico y la repercusión prevista del proyecto financiado.
Convocatoria de propuestas
Procedimiento para invitar a los solicitantes a presentar propuestas de proyectos con el objetivo de obtener financiación de la UE.
Datos no disponibles
Procedimiento para invitar a los solicitantes a presentar propuestas de proyectos con el objetivo de obtener financiación de la UE.
Régimen de financiación
Régimen de financiación (o «Tipo de acción») dentro de un programa con características comunes. Especifica: el alcance de lo que se financia; el porcentaje de reembolso; los criterios específicos de evaluación para optar a la financiación; y el uso de formas simplificadas de costes como los importes a tanto alzado.
Régimen de financiación (o «Tipo de acción») dentro de un programa con características comunes. Especifica: el alcance de lo que se financia; el porcentaje de reembolso; los criterios específicos de evaluación para optar a la financiación; y el uso de formas simplificadas de costes como los importes a tanto alzado.
Coordinador
AACHEN
Alemania
Los costes totales en que ha incurrido esta organización para participar en el proyecto, incluidos los costes directos e indirectos. Este importe es un subconjunto del presupuesto total del proyecto.