Objectif
Conclusions on sampling:
The sampling, in the forest and/or in the industry, has covered a wide range of species and sizes. A minimum of 900 pieces is required for the derivation of settings for a new machine with the full range of sizes and grades. The sampling of TIMGRAD (1600 pieces for FRANCE; 900 pieces for UK; 450 pieces for SW) is within this limit. In fact, a sampling method in order to decrease the amount of testing needed has been investigated (SW). The number of specimens was decreased by 80-90% without affecting the relations between the mechanical properties of the material and the tested non-destructive properties.
Conclusions on NDT:
A lot of techniques applicable to timber strength grading have been studied: Some already existed (ScanWood, Metriguard, Cook Bolinder, Computermatic) and other ones have been set up during the project as follows
The SNTRI camera is based on a smart sensor technique together with line-lasers. With this system it was possible to detect knots on Norway spruce timber with a sawn surface, which is generally very difficult with normal camera systems.
By analysing the frequency response of the timber the modulus of elasticity can be determined. This technique available in Sweden enables cross transportation of the timber, which is the normal way of transporting timber at sawmills. The technique works as good as the bending type machines, although it does not measures the local timber characteristics, but rather the global behaviour of each piece of timber.
CTBA introduce X rays device in the project to measure local density. The previous work (Rouger 1994) has shown good correlations between the non destructive parameters and the mechanical properties. The results obtained in TIMGRAD show that the X rays device is quite the best machine.
BRE would recommend further development of the Metriguard ELDECO device, for the devices tested in the UK. There are several reasons for this;
a). It appears to provide the most reliability in operation
b). The operating algorithms are less complicated.
c). The calibration procedures for the device are the simplest and the most straight forward.
d) despite a considerable amount during its development (software), it stills shows problems in use.
e) the calibration of the device will be difficult to prove.
BRE strongly recommends further investigation and development of the electronic noise filtration technology on strength machine. Indications explain that this technology offers the quickest and most cost effective way to produce significant cost benefits for the Sawmillers, although there is still a need for more experimental work to define the magnitude of the benefits. Two particular methods offer the greatest potential;
i)improving the prediction of strength by improving the correlation coeffiecient.
ii)By filtering out frequencies there is a component of the grading machine speed, thereby allowing the grading machines to be run faster.
The smart camera system is not a method with enough accuracy by itself for timber strength grading, but coupled with other techniques, such as the bending machines, grading accuracy can be increased. The camera system studied has the advantage that it can detect knots on sawn surfaces of species such as Norway spruce, which is normally very difficult with camera techniques. Furthermore, using the camera system an appearance grading can be performed, which is of great importance for certain products such as gluelam lamellas. The Maritime Pine is "Red Wood" species. During the measurements of nodosity, it has created difficulties (difference of contrast with Spruce species).
Champ scientifique (EuroSciVoc)
CORDIS classe les projets avec EuroSciVoc, une taxonomie multilingue des domaines scientifiques, grâce à un processus semi-automatique basé sur des techniques TLN. Voir: Le vocabulaire scientifique européen.
CORDIS classe les projets avec EuroSciVoc, une taxonomie multilingue des domaines scientifiques, grâce à un processus semi-automatique basé sur des techniques TLN. Voir: Le vocabulaire scientifique européen.
- sciences naturelles informatique et science de l'information logiciel
- ingénierie et technologie génie électrique, génie électronique, génie de l’information ingénierie électronique capteurs capteurs optiques
- ingénierie et technologie génie électrique, génie électronique, génie de l’information ingénierie électronique capteurs capteurs intelligents
- sciences agricoles agriculture, sylviculture et pêche sylviculture
Vous devez vous identifier ou vous inscrire pour utiliser cette fonction
Programme(s)
Programmes de financement pluriannuels qui définissent les priorités de l’UE en matière de recherche et d’innovation.
Programmes de financement pluriannuels qui définissent les priorités de l’UE en matière de recherche et d’innovation.
Thème(s)
Les appels à propositions sont divisés en thèmes. Un thème définit un sujet ou un domaine spécifique dans le cadre duquel les candidats peuvent soumettre des propositions. La description d’un thème comprend sa portée spécifique et l’impact attendu du projet financé.
Données non disponibles
Les appels à propositions sont divisés en thèmes. Un thème définit un sujet ou un domaine spécifique dans le cadre duquel les candidats peuvent soumettre des propositions. La description d’un thème comprend sa portée spécifique et l’impact attendu du projet financé.
Appel à propositions
Procédure par laquelle les candidats sont invités à soumettre des propositions de projet en vue de bénéficier d’un financement de l’UE.
Données non disponibles
Procédure par laquelle les candidats sont invités à soumettre des propositions de projet en vue de bénéficier d’un financement de l’UE.
Régime de financement
Régime de financement (ou «type d’action») à l’intérieur d’un programme présentant des caractéristiques communes. Le régime de financement précise le champ d’application de ce qui est financé, le taux de remboursement, les critères d’évaluation spécifiques pour bénéficier du financement et les formes simplifiées de couverture des coûts, telles que les montants forfaitaires.
Régime de financement (ou «type d’action») à l’intérieur d’un programme présentant des caractéristiques communes. Le régime de financement précise le champ d’application de ce qui est financé, le taux de remboursement, les critères d’évaluation spécifiques pour bénéficier du financement et les formes simplifiées de couverture des coûts, telles que les montants forfaitaires.
Coordinateur
75012 Paris
France
Les coûts totaux encourus par l’organisation concernée pour participer au projet, y compris les coûts directs et indirects. Ce montant est un sous-ensemble du budget global du projet.