Cel
Conclusions on sampling:
The sampling, in the forest and/or in the industry, has covered a wide range of species and sizes. A minimum of 900 pieces is required for the derivation of settings for a new machine with the full range of sizes and grades. The sampling of TIMGRAD (1600 pieces for FRANCE; 900 pieces for UK; 450 pieces for SW) is within this limit. In fact, a sampling method in order to decrease the amount of testing needed has been investigated (SW). The number of specimens was decreased by 80-90% without affecting the relations between the mechanical properties of the material and the tested non-destructive properties.
Conclusions on NDT:
A lot of techniques applicable to timber strength grading have been studied: Some already existed (ScanWood, Metriguard, Cook Bolinder, Computermatic) and other ones have been set up during the project as follows
The SNTRI camera is based on a smart sensor technique together with line-lasers. With this system it was possible to detect knots on Norway spruce timber with a sawn surface, which is generally very difficult with normal camera systems.
By analysing the frequency response of the timber the modulus of elasticity can be determined. This technique available in Sweden enables cross transportation of the timber, which is the normal way of transporting timber at sawmills. The technique works as good as the bending type machines, although it does not measures the local timber characteristics, but rather the global behaviour of each piece of timber.
CTBA introduce X rays device in the project to measure local density. The previous work (Rouger 1994) has shown good correlations between the non destructive parameters and the mechanical properties. The results obtained in TIMGRAD show that the X rays device is quite the best machine.
BRE would recommend further development of the Metriguard ELDECO device, for the devices tested in the UK. There are several reasons for this;
a). It appears to provide the most reliability in operation
b). The operating algorithms are less complicated.
c). The calibration procedures for the device are the simplest and the most straight forward.
d) despite a considerable amount during its development (software), it stills shows problems in use.
e) the calibration of the device will be difficult to prove.
BRE strongly recommends further investigation and development of the electronic noise filtration technology on strength machine. Indications explain that this technology offers the quickest and most cost effective way to produce significant cost benefits for the Sawmillers, although there is still a need for more experimental work to define the magnitude of the benefits. Two particular methods offer the greatest potential;
i)improving the prediction of strength by improving the correlation coeffiecient.
ii)By filtering out frequencies there is a component of the grading machine speed, thereby allowing the grading machines to be run faster.
The smart camera system is not a method with enough accuracy by itself for timber strength grading, but coupled with other techniques, such as the bending machines, grading accuracy can be increased. The camera system studied has the advantage that it can detect knots on sawn surfaces of species such as Norway spruce, which is normally very difficult with camera techniques. Furthermore, using the camera system an appearance grading can be performed, which is of great importance for certain products such as gluelam lamellas. The Maritime Pine is "Red Wood" species. During the measurements of nodosity, it has created difficulties (difference of contrast with Spruce species).
Dziedzina nauki (EuroSciVoc)
Klasyfikacja projektów w serwisie CORDIS opiera się na wielojęzycznej taksonomii EuroSciVoc, obejmującej wszystkie dziedziny nauki, w oparciu o półautomatyczny proces bazujący na technikach przetwarzania języka naturalnego. Więcej informacji: Europejski Słownik Naukowy.
Klasyfikacja projektów w serwisie CORDIS opiera się na wielojęzycznej taksonomii EuroSciVoc, obejmującej wszystkie dziedziny nauki, w oparciu o półautomatyczny proces bazujący na technikach przetwarzania języka naturalnego. Więcej informacji: Europejski Słownik Naukowy.
- nauki przyrodnicze informatyka oprogramowanie
- inżynieria i technologia inżynieria elektryczna, inżynieria elektroniczna, inżynieria informatyczna inżynieria elektroniczna czujniki czujniki optyczne
- inżynieria i technologia inżynieria elektryczna, inżynieria elektroniczna, inżynieria informatyczna inżynieria elektroniczna czujniki inteligentne czujniki
- nauki rolnicze rolnictwo, leśnictwo i rybołówstwo leśnictwo
Aby użyć tej funkcji, musisz się zalogować lub zarejestrować
Program(-y)
Wieloletnie programy finansowania, które określają priorytety Unii Europejskiej w obszarach badań naukowych i innowacji.
Wieloletnie programy finansowania, które określają priorytety Unii Europejskiej w obszarach badań naukowych i innowacji.
Temat(-y)
Zaproszenia do składania wniosków dzielą się na tematy. Każdy temat określa wybrany obszar lub wybrane zagadnienie, których powinny dotyczyć wnioski składane przez wnioskodawców. Opis tematu obejmuje jego szczegółowy zakres i oczekiwane oddziaływanie finansowanego projektu.
Brak dostępnych danych
Zaproszenia do składania wniosków dzielą się na tematy. Każdy temat określa wybrany obszar lub wybrane zagadnienie, których powinny dotyczyć wnioski składane przez wnioskodawców. Opis tematu obejmuje jego szczegółowy zakres i oczekiwane oddziaływanie finansowanego projektu.
Zaproszenie do składania wniosków
Procedura zapraszania wnioskodawców do składania wniosków projektowych w celu uzyskania finansowania ze środków Unii Europejskiej.
Brak dostępnych danych
Procedura zapraszania wnioskodawców do składania wniosków projektowych w celu uzyskania finansowania ze środków Unii Europejskiej.
System finansowania
Program finansowania (lub „rodzaj działania”) realizowany w ramach programu o wspólnych cechach. Określa zakres finansowania, stawkę zwrotu kosztów, szczegółowe kryteria oceny kwalifikowalności kosztów w celu ich finansowania oraz stosowanie uproszczonych form rozliczania kosztów, takich jak rozliczanie ryczałtowe.
Program finansowania (lub „rodzaj działania”) realizowany w ramach programu o wspólnych cechach. Określa zakres finansowania, stawkę zwrotu kosztów, szczegółowe kryteria oceny kwalifikowalności kosztów w celu ich finansowania oraz stosowanie uproszczonych form rozliczania kosztów, takich jak rozliczanie ryczałtowe.
Koordynator
75012 Paris
Francja
Ogół kosztów poniesionych przez organizację w związku z uczestnictwem w projekcie. Obejmuje koszty bezpośrednie i pośrednie. Kwota stanowi część całkowitego budżetu projektu.