Periodic Reporting for period 1 - PROMETEO (Hydrogen PROduction by MEans of solar heat and power in high TEmperature Solid Oxide Electrolysers)
Berichtszeitraum: 2021-01-01 bis 2022-06-30
Green hydrogen production at low-cost will foster the decarbonization of hard-to-abate industrial sectors (e.g. the chemical, steel, fertilizer industry); hydrogen can replace natural gas in the gas infrastructure and also improve the management of power grids with increasing RES footprint.
In this context, the project PROMETEO proposes a solution for green hydrogen production from renewable heat & power sources by high temperature electrolysis in areas of low electricity prices associated to photovoltaic or wind.
Solid Oxide Electrolysis (SOE) is a highly efficient technology to convert heat & power into hydrogen from water usually validated in steady-state operation. However, the heat for steam generation may not be available for the operation of the SOE when inexpensive power is offered (e.g. off-grid peak, photovoltaics or wind). Thus, the challenge is to optimize the coupling of the SOE with two intermittent sources: non-programmable renewable electricity and high-temperature solar heat from Concentrating Solar (CS) systems with Thermal Energy Storage (TES) to supply solar heat when power is made available.
In PROMETEO a fully integrated optimized system will be developed, where the SOE combined with the TES and ancillary components will efficiently convert intermittent heat & power sources to hydrogen. The design will satisfy different criteria: end-users’ needs, sustainability aspects, regulatory & safety concerns, scale-up and engineering issues.
A fully-equipped modular prototype with at least 25 kWe SOE (about 15 kg/day hydrogen production) and TES will be designed, built, connected to representative external power/heat sources and validated in real context (TRL 5). Particular attention will be given to partial load operation, transients and hot stand-by periods.
Industrial end-users will lead to techno-economic and sustainability studies to apply the technology in on-grid and off-grid scenarios and for different end-uses: utility for grid balancing, power-to-gas, and hydrogen as feedstock for the fertilizer and chemical industry.
During the 1st Period of the project (Months 1-18) the above “phase 1” was mainly implemented in work packages 2, 3, and 4.
The project started with the assessment of end-users’ requirements, the development of preliminary PFD and the identification of basic units’ specifications (WP2).
Key components of PROMETEO system (namely the SOE, TES-SG and plant BoP) were identified, designed and manufactured (WP3); individual testing/characterization of these key components started by the end of the 1st Period.
In the meantime, developed process schemes (WP2) were further analysed with modelling and simulation activities in order to assess the possibility to reach the target and KPI of the project (WP4).
Additionally, during the last months of the 1st Period, engineering activities started for the design of PROMETEO prototype (WP5).
Results obtained during the 1st Period will be exploited during the 2nd Period for the final design and construction of PROMETEO prototype (WP5), to be finally tested during the 3rd Period in relevant environment (WP6). Obtained results will also provide input to the techno-economic assessment and case studies (WP7).
To advance the state-of-the-art, the project PROMETEO addresses key innovations involving the development and validation in a relevant environment of an ad-hoc stack fed with steam from a representative thermal energy storage unit. The necessary innovation in the simulation field is also needed to establish a portfolio of toolboxes for optimization, system performance analysis and dynamic performance analysis, as well as the elaboration of reliable end-use studies at commercial level, thanks to the inclusion of three end-users in the Consortium.
More in detail, the following key innovations are expected from the PROMETEO project:
• Development and testing of a fully integrated low-cost and high-performance SOE with at least 25 kWe power capacity; the expected yield in electrolysis mode will be 15 kgH2/day for a power consumption of 25 kWe.
• Demonstration of the SOE operation for at least 1,000 hours in relevant environment (TRL 5).
• Demonstration of heat integration with Concentrating Solar by the first-ever adaption of a specific Thermal Energy Storage (TES) system to operate in an integrated way with SOE technology. The innovation will lead to a customized TES/Steam Generation system to produce stable steam at 150ºC by means of molten salts.
• Development of advanced system analysis toolboxes for process integration optimization and performance analysis under steady state and dynamic conditions, to assess optimum integration solutions of SOE with solar heat and PV/wind power generation technologies.
• A reliable up-scaling to multi-MWe analysis for integrated end-use applications in grid balancing, power-to-gas and in chemical industry.
The above innovation targets will potentially provide a solution for low-cost green hydrogen production to foster the decarbonization of hard-to-abate industrial and energy sectors; besides contributing to the mitigation of climate change and the safe access to low-cost energy carriers, PROMETEO will lead to potential societal benefits such as new job creation in the emerging green economy.