Optimization two phases cooling solution using micro pump brick

Projektinformationen

TOPMOST

ID Finanzhilfevereinbarung: 738094

DOI

10.3030/738094

Projekt abgeschlossen

EK-Unterschriftsdatum 17 Januar 2017

Startdatum 1 Februar 2017

Enddatum 31 Mai 2019

Finanziert unter

• SOCIETAL CHALLENGES - Smart, Green And Integrated Transport

Gesamtkosten

€ 711 810,00

EU-Beitrag

€ 711 810,00

Koordiniert durch

STICHTING KONINKLIJK NEDERLANDS LUCHT - EN RUIMTEVAARTCENTRUM
Netherlands

Periodic Reporting for period 1 - TOPMOST (Optimization two phases cooling solution using micro pump brick)

Berichtszeitraum: 2017-02-01 bis 2019-05-31

Zusammenfassung vom Kontext und den Gesamtzielen des Projekts

The amount of waste heat that is generated in electronic components in aerospace application is increasing because of higher electrical power demands. As a result, conventional cooling methods are not able to maintain the electronic component below its maximum temperature. For this reason, a two-phase Mechanically Pumped Fluid Loop has been developed for high-power electronic components in a commercial aerospace application. These electronic components generate a waste heat of 1200 W that is divided over several hotspots while the temperature gradient over the component has to be kept to a minimum. The developed cooling system uses R245fa as refrigerant and is made from aluminum components produced with additive manufacturing. The use of this novel production technique results in an unprecedented low system mass (2.5 kg) and small system dimensions. Measurements show that the system has an excellent thermal performance and is able to cool 2400W (so two times the initial requirement). The system has passed vibration and salt spray tests.

Arbeit, die ab Beginn des Projekts bis zum Ende des durch den Bericht erfassten Berichtszeitraums geleistet wurde, und die wichtigsten bis dahin erzielten Ergebnisse

In the preliminary design phase of the project, R245fa has been selected as the working fluid of the thermal control system, because of its non-flammability, low toxicity, and excellent thermal performance. Initial tests have been carried out with this fluid on several heat exchanger samples, and these tests show an excellent cooling performance. Many parts of the system will be manufactured with 3D metal printing of aluminum, and several tests have been carried out to select the best aluminum alloy and the optimal printing process parameters.

In the detail design phase of the project, several tests were carried out in order to reduce the risks of new technologies that are used in the TOPMOST system. These tests include corrosions tests on 3D printed aluminium samples and orbital welding tests. This resulted in a complete detail design for the two-phase system, including CAD drawings, a list of components, and FEM analyses.

During the construction phase of the project, 3 demonstrators have been built. Two of the demonstrators have be delivered to Thales Avionics Electrical Systems, and one demonstrator has been used for qualification tests.

In the test phase of the project, thermal, vibration and salt spray tests have been carried out. The demonstrators have an excellent thermal performance, and the tested system has passed the environmental tests.

The TOPMOST project has resulted in 3 peer reviewed conference papers. The TOPMOST work was presented at these three conferences and also at 1 workshop. Furthermore, the TOPMOST results were presented at three exhibitions.

Fortschritte, die über den aktuellen Stand der Technik hinausgehen und voraussichtliche potenzielle Auswirkungen (einschließlich der bis dato erzielten sozioökonomischen Auswirkungen und weiter gefassten gesellschaftlichen Auswirkungen des Projekts)

The TOPMOST project has resulted in demonstrators for a cooling system that can cool a much higher heat load with a much lower mass than conventional cooling systems. This novel cooling system enables more powerful electronics on More Electric Aircraft. The project results can also be used for space applications, for example in the H2020-SPACE-2018 IMPACTA (822027) project. In this project, the objective is to build a two-phase cooling system for active antennae for space applications. The consortium for this project includes manufactures of the component and the final customer of the cooling systems.

f19053-01l.jpg

f19053-08l.jpg

f19053-27l.jpg

f19053-09l.jpg