Innovative Tooling, End-Effector Development and Industrialisation for Welding of Thermoplastic Components

Projektinformationen

TCTOOL

ID Finanzhilfevereinbarung: 865131

DOI

10.3030/865131

Projekt abgeschlossen

EK-Unterschriftsdatum 12 September 2019

Startdatum 1 Oktober 2019

Enddatum 31 Oktober 2021

Finanziert unter

• SOCIETAL CHALLENGES - Smart, Green And Integrated Transport

Gesamtkosten

€ 1 101 836,63

EU-Beitrag

€ 1 049 357,25

Koordiniert durch

TWI LIMITED
United Kingdom

Periodic Reporting for period 2 - TCTOOL (Innovative Tooling, End-Effector Development and Industrialisation for Welding of Thermoplastic Components)

Berichtszeitraum: 2020-10-01 bis 2021-10-31

Zusammenfassung vom Kontext und den Gesamtzielen des Projekts

Weight reduction is an ongoing challenge for aircraft manufacturers as they have to meet international targets for emission reduction and to improve capacity and return on investment for customers. Thermoplastic composites can be a very well suited solution as they can save more weight compared to thermoset composites.
The overall target of the TCTool project is the assembly of different parts of a fuselage demonstrator efficiently and with low cost. For a conventional assembly, fixed tooling is dedicated to specific set of products. As there is an increasing demand for larger number of aircrafts, for the case of new products, new tooling is necessary. At the same time, tooling accounts for one third of total non-recurring costs, and jigs are a major element of tooling and of the total cost of manufacture.
For the case of a thermoplastic assembly, in order to make the most out of their advantages, it is necessary to combine high degree of automation and cost reduction in the assembly. This can happen through the development of:
• Single, highly automated and configurable robotic assembly to replace a number of jigs
• End-effectors to deliver heat and pressure into the joint
• Assembly tooling for automated welding of fuselage components
TCTool project aims to develop innovative solutions to address the requirements for tooling and end-effector development for thermoplastic composite assembly of fuselage components. More precisely, the objectives of the project are the following:
• Develop innovative end effectors for picking and placing of fuselage components
• Develop innovative end-effector for welding
• Develop assembly tool for welding of fuselage components
• Digital-twin with direct link to jig-less tooling to:
o Provide change-controlled model capability
o Provide capability to analyse and visualize data rapidly
The findings from TCTool project are expected to have significant societal impact. Training and nurturing future leaders in innovation, business and science and technology research is essential for developing new products and services that will ensure the future prosperity of European citizens. TCTool can provide an excellent example of industrially driven new technologies, supporting an industry where European companies are world-leading. In particular, it has supported the development of new expertise and transfer new robotic technology from the research base into future products and revenue generation.
According to the aforementioned objectives, the TCTool project has successfully managed to deliver the three end-effectors namely:
1) Pick and place end-effector
2) Welding end-effector
3) Weld jig
Finally, the robotic process simulation was successfully performed based on the development of the three end-effectors that were mentioned above.

Arbeit, die ab Beginn des Projekts bis zum Ende des durch den Bericht erfassten Berichtszeitraums geleistet wurde, und die wichtigsten bis dahin erzielten Ergebnisse

The first reporting period of TCTool project has finished with significant progress performed by all the partners. More precisely, partner LSBU, have designed an innovative short-welds end-effector that is capable of manoeuvring its way to reach difficult spots within the fuselage assembly. TWI, have developed a first design of an adaptable jig that will support the entire assembly and assist in the welding process of the stringers to the skin. The placement and welding of stringers and clips will be performed with a multipurpose end-effector which was fully designed and developed by partner CATEC. LSBU’s and CATEC’s end-effectors will both be supported by a gantry. Finally, during this period, partner ACRO have outlined the functions and progress of the digital twin that will oversee and provide a complete description of the product.

During the final period of the TCTool project, the pick and place end-effector was successfully delivered to the Topic Manager’s facilities and a fully detailed integration manual was provided for the installation of the end effector in Holland (D2.2). Similarly, for the case of the welding end-effector, this was successfully delivered to the Topic Manager’s facilities along with the deliverable that includes all the relevant information (D3.2). The last end-effector that was delivered successfully was the weld jig. A deliverable describing the functionality of the weld jig and the way to assemble it at the Topic Manager’s facilities was produced (D4.2). Finally, the robotic process simulation was performed based on the development of the three end-effectors. The project findings have been widely disseminated during the final period of the project namely:
1) EASN conference 1-3 September 2021 (https://easnconference.eu/)
2) EASN Conference paper
3) Peer reviewed research article (https://link.springer.com/article/10.1007/s00170-021-07829-2)

Fortschritte, die über den aktuellen Stand der Technik hinausgehen und voraussichtliche potenzielle Auswirkungen (einschließlich der bis dato erzielten sozioökonomischen Auswirkungen und weiter gefassten gesellschaftlichen Auswirkungen des Projekts)

The key advantages of thermoplastic composites are their weldability, low density, low overall production cost, improved fracture toughness and recyclability. These benefits are utilised by TCTool project with the aim to go beyond the state of the art and industrialise the use of advanced thermoplastics to manufacture multifunctional fuselages. More precisely, the development of the three end-effectors from the project partners LSBU, CATEC and TWI has demonstrated the feasibility of assembling a 180o full scale multifunctional integrated thermoplastic lower fuselage shell, including cabin and cargo floor structure. The new assembly technologies developed in TCTOOL are critical to the realisation of integrating bigger and more complex composite structures in aircraft which will help ensure the future competitiveness of European aircraft manufacturers their world-leading market position. This competitiveness will require the rapid flow of new technologies such as TCTOOL into production to remain ahead of competitors in North America and increasing competition from Brazil and China. The TCTOOL consortium also has strong links with SME specialists which will enable the technology to support the growth and future competitiveness of these companies, laying the basis for future wealth generation within Europe. Finally, training and nurturing future leaders in innovation, business and science and technology research is essential for developing new products and services that will ensure the future prosperity of European citizens. This project has provided an excellent example of industrially driven new technologies, supporting an industry where European companies are world-leading. In particular, it has supported the development of new expertise and transfer new robotic technology from the research base into future products and revenue generation.

TCTool logo