Obiettivo
Guidelines for design of CRC have been set up, and results have confirmed that the material is well suited for a plastic analysis. CRC columns have been designed without stirrups - with satisfactory test results, and the possibility of omitting shear reinforcement in beams has been established. In order to accomplish the task of preparing the design guidelines, it was decided at an early stage of the project to perform almost all tests with one particular CRC composition. For this reason a correlation between mix design and structural design is not well established, but the effect on mechanical properties of exchanging types of fibres has been investigated.
Tests on durability - corrosion as well as fire resistance - have also been encouraging, as even very rigorous testing have not led to active corrosion after more than two years of exposure. There is practically no danger of corrosion of reinforcing bars, even with a low thickness of cover to the reinforcement, due to the low porosity of CRC. Even with a chloride content in the mix water which is higher than the expected critical threshold value, no corrosion is observed. Chemical resistance is high, there is practically no effect of carbonation and light drying of structural components appear to prevent spalling under fire exposure.
Investigations with regard to production techniques were aimed at transferring the technology from laboratory level to full scale production, and one of the results was that mixing time has decreased from 18 minutes at the beginning of the project to 8 minutes used in production of specimens for full scale tests.
Procedures for in-situ casting has only been touched upon briefly as most of the production has been carried out as pre-cast. However, a CRC application has been implemented during the project, where the material was used for in-situ cast joints at Aalborg University. This application was part of another project led by the Carl Bro Group, which, however, supplemented the MINISTRUCT project well. As no problems were encountered in connection with the Carl Bro Group project, it has been decided to invest efforts set aside for this investigation of in-situ casting at other tasks.
Full scale tests - incorporating the knowledge gained in the project with regard to design, mixing and casting technology - have been carried out in the project, where large beams and columns have been produced and tested. Full scale joints have also been produced and tested.
The proposed research is directed at introduction of the concept of Minimal structures using ultra high strength concrete in civil engineering construction. In Minimal structures the material content is minimized by the use of a new ultra high strength concrete (CRC) with improved performance compared to contemporarily used materials, thus significantly reducing resource consumption (raw materials, energy) and environmental impact (refuse, pollution etc...). The major research tasks are:
- laboratory test on durability, i.e. corrosion and fire resistance
- laboratory tests on structural properties, i.e. creep and shrinkage, optimization of fibre content, anchorage and behaviour in bending
- production tests for large scale production and in situ casting
- structural analysis necessary for establishing guidelines
- design production, and testing of full scale prototypes .
Preliminary calculations have indicated that utilization of this new type of reinforced concrete in the manufacture of various structural members (beams, girders, columns, plates, etc...) may lead to considerable savings (up to app. 80%) in materials (and consequently in weight) as compared to the alternative uses of either conventional reinforced concrete or structural steel.
Campo scientifico (EuroSciVoc)
CORDIS classifica i progetti con EuroSciVoc, una tassonomia multilingue dei campi scientifici, attraverso un processo semi-automatico basato su tecniche NLP. Cfr.: Il Vocabolario Scientifico Europeo.
CORDIS classifica i progetti con EuroSciVoc, una tassonomia multilingue dei campi scientifici, attraverso un processo semi-automatico basato su tecniche NLP. Cfr.: Il Vocabolario Scientifico Europeo.
- ingegneria e tecnologia ingegneria civile
- scienze naturali scienze della terra e scienze ambientali connesse scienze ambientali inquinamento
È necessario effettuare l’accesso o registrarsi per utilizzare questa funzione
Siamo spiacenti… si è verificato un errore inatteso durante l’esecuzione.
È necessario essere autenticati. La sessione potrebbe essere scaduta.
Grazie per il tuo feedback. Riceverai presto un'e-mail di conferma dell'invio. Se hai scelto di ricevere una notifica sullo stato della segnalazione, sarai contattato anche quando lo stato della segnalazione cambierà.
Programma(i)
Programmi di finanziamento pluriennali che definiscono le priorità dell’UE in materia di ricerca e innovazione.
Programmi di finanziamento pluriennali che definiscono le priorità dell’UE in materia di ricerca e innovazione.
Argomento(i)
Gli inviti a presentare proposte sono suddivisi per argomenti. Un argomento definisce un’area o un tema specifico per il quale i candidati possono presentare proposte. La descrizione di un argomento comprende il suo ambito specifico e l’impatto previsto del progetto finanziato.
Gli inviti a presentare proposte sono suddivisi per argomenti. Un argomento definisce un’area o un tema specifico per il quale i candidati possono presentare proposte. La descrizione di un argomento comprende il suo ambito specifico e l’impatto previsto del progetto finanziato.
Invito a presentare proposte
Procedura per invitare i candidati a presentare proposte di progetti, con l’obiettivo di ricevere finanziamenti dall’UE.
Dati non disponibili
Procedura per invitare i candidati a presentare proposte di progetti, con l’obiettivo di ricevere finanziamenti dall’UE.
Meccanismo di finanziamento
Meccanismo di finanziamento (o «Tipo di azione») all’interno di un programma con caratteristiche comuni. Specifica: l’ambito di ciò che viene finanziato; il tasso di rimborso; i criteri di valutazione specifici per qualificarsi per il finanziamento; l’uso di forme semplificate di costi come gli importi forfettari.
Meccanismo di finanziamento (o «Tipo di azione») all’interno di un programma con caratteristiche comuni. Specifica: l’ambito di ciò che viene finanziato; il tasso di rimborso; i criteri di valutazione specifici per qualificarsi per il finanziamento; l’uso di forme semplificate di costi come gli importi forfettari.
Coordinatore
9100 AALBORG
Danimarca
I costi totali sostenuti dall’organizzazione per partecipare al progetto, compresi i costi diretti e indiretti. Questo importo è un sottoinsieme del bilancio complessivo del progetto.