Ziel
The aim is to reduce the variability of the rubber mixes and to improve their quality level.
The objectives of the project are to determine close relationships between mixing parameters, dispersion measurements and mix properties, to develop an innovative closed loop control system capable of providing the quality of the mix in real time, to compare the efficiency of the 2 main types of internal mixer present on the market and to reduce the variability of the rubber mixes and to improve their quality level.
An improvement in batch variability has been found with the resulting problem of interpreting the results of the factorial experimental design. A new design is in progress to solve this problem. Dispersion measurement techniques show that electrical and dielectrical methods and image analysis have been improved significantly. An innovative control system has been designed and manufactured and promising results obtained, but the response time still remains to be reduced.
Three types of industrial rubber mixes, containing natural rubber, ethylenepropylene terpolymer rubber, and a blend of cis polybutadiene and cis polyisoprene rubbers, reinforced with carbon black, have been prepared. Using computer controlled Francis Shaw (FS) K1 intermeshing rotor internal mixers of 5.5 litres capacity, factorial experiments were designed to investigate the effect of mixer variables, ie rotor speed and mixing energy and/or mixing time, on physical properties and their interrelationships. A well instrumented 2 roll rubber mill was included in the experiment to investigate mill variables, ie mill speed, nip setting, friction ratio and number of passes through the nip.
A statistical package (GLIM) was used to analyse the results of a range of physical property measurements covering rheology, cure characteristics, carbon black dispersion and mechancial properties. The only significant effects were a dependence on mixer rotor speed and a difference between the performance of the similar mixers.
In addition, no significant relationships were found between pairs of physical properties which would have permitted reduced testing. It was concluded that mix inhomogeneity was masking mixer/milling effects, at least for failure properties, ie those particularly sensitive to residual aggregates of carbon black. Effort was therefore concentrated on reducing that inhomogeneity.
Several methods for determination of the all important carbon black dispersion have been evaluated and developed. Instruments are recommended for detection of poor to medium dispersions, and for quantifying good dispersions, on a routine production control basis. Another is recommended as a research tool for examining carbon black distribution using sample sizes of a few square millimetres.
A device has been developed and tested to enable measurements of compound viscosity to be made during the mixing process; the output of the device can be used to control the discharge of compound with the desired viscosity.
Consideration is now being given to maximizing the benefits of the new equipment and methodologies developed. Plants will be selected for initial implementations and their experiences will be used as case studies for training of other mixing plants.
In addition to waste reduction, the results will also enable operating costs to be reduced.
Serious consideration is also being given to the development of a commercially available sensor which will be incorporated into a closed loop system. Exploitation of the sensor is expected to extend to retrofitting to existing mixing installations, in addition to provision with new mixers.
There is a strong market requirement to increase the quality of the rubber parts as well as to tighten their performance.
Therefore the objectives of the project are:
-To determine close relationships between mixing parameters, dispersion measurements and mix properties.
-To develop an innovative closed-loop control system capable of providing the quality of the mix in real-time.
-To compare the efficiency of the two main types of internal mixer present on the market.
Wissenschaftliches Gebiet (EuroSciVoc)
CORDIS klassifiziert Projekte mit EuroSciVoc, einer mehrsprachigen Taxonomie der Wissenschaftsbereiche, durch einen halbautomatischen Prozess, der auf Verfahren der Verarbeitung natürlicher Sprache beruht. Siehe: Das European Science Vocabulary.
CORDIS klassifiziert Projekte mit EuroSciVoc, einer mehrsprachigen Taxonomie der Wissenschaftsbereiche, durch einen halbautomatischen Prozess, der auf Verfahren der Verarbeitung natürlicher Sprache beruht. Siehe: Das European Science Vocabulary.
- Technik und Technologie Elektrotechnik, Elektronik, Informationstechnik Elektrotechnik Steuerungssysteme
- Technik und Technologie Elektrotechnik, Elektronik, Informationstechnik Elektrotechnik Sensoren
Sie müssen sich anmelden oder registrieren, um diese Funktion zu nutzen
Programm/Programme
Mehrjährige Finanzierungsprogramme, in denen die Prioritäten der EU für Forschung und Innovation festgelegt sind.
Mehrjährige Finanzierungsprogramme, in denen die Prioritäten der EU für Forschung und Innovation festgelegt sind.
Thema/Themen
Aufforderungen zur Einreichung von Vorschlägen sind nach Themen gegliedert. Ein Thema definiert einen bestimmten Bereich oder ein Gebiet, zu dem Vorschläge eingereicht werden können. Die Beschreibung eines Themas umfasst seinen spezifischen Umfang und die erwarteten Auswirkungen des finanzierten Projekts.
Daten nicht verfügbar
Aufforderungen zur Einreichung von Vorschlägen sind nach Themen gegliedert. Ein Thema definiert einen bestimmten Bereich oder ein Gebiet, zu dem Vorschläge eingereicht werden können. Die Beschreibung eines Themas umfasst seinen spezifischen Umfang und die erwarteten Auswirkungen des finanzierten Projekts.
Aufforderung zur Vorschlagseinreichung
Verfahren zur Aufforderung zur Einreichung von Projektvorschlägen mit dem Ziel, eine EU-Finanzierung zu erhalten.
Daten nicht verfügbar
Verfahren zur Aufforderung zur Einreichung von Projektvorschlägen mit dem Ziel, eine EU-Finanzierung zu erhalten.
Finanzierungsplan
Finanzierungsregelung (oder „Art der Maßnahme“) innerhalb eines Programms mit gemeinsamen Merkmalen. Sieht folgendes vor: den Umfang der finanzierten Maßnahmen, den Erstattungssatz, spezifische Bewertungskriterien für die Finanzierung und die Verwendung vereinfachter Kostenformen wie Pauschalbeträge.
Finanzierungsregelung (oder „Art der Maßnahme“) innerhalb eines Programms mit gemeinsamen Merkmalen. Sieht folgendes vor: den Umfang der finanzierten Maßnahmen, den Erstattungssatz, spezifische Bewertungskriterien für die Finanzierung und die Verwendung vereinfachter Kostenformen wie Pauschalbeträge.
Daten nicht verfügbar
Koordinator
75384 Paris
Frankreich
Die Gesamtkosten, die dieser Organisation durch die Beteiligung am Projekt entstanden sind, einschließlich der direkten und indirekten Kosten. Dieser Betrag ist Teil des Gesamtbudgets des Projekts.