Obiettivo
To demonstrate the overall thermal improvement to an alumina digestion process with the introduction of an injection heater utilising regenerative steam for pre-heating. The feed slurry has high scaling properties and is very abrasive.
The technique involves the use of regenerative steam to heat the slurry in a specially developed injection heater constructed from hardened, ductile steel and stainless steel with "Spray Stelliting" for enhanced wear resistance.
The overall thermal input to the plant will be reduced by 7,902 TOE/Annum; also, 144,452 tonnes of treated water should be saved annually.
With present systems the Bauxite slurry is pumped into the digester relatively cold. Due to the high scaling and abrasive nature of the standard method of pre-heating using in-line injection has not been successful. The standard injection system attempted consisted of a series of holes around the circumference of the slurry flow pipe. Erosion and blockages gave serious problems resulting in poor mixing and heat transfer.
The new injection system has been previously used to heat water and slurries in the chemical and paper pulp industries, however, these applications are at low temperatures, below 120 deg. C. To cater for the higher temperatures required for this application a special injection heater has been designed using hardened, ductile steel (hardened to 450 Brinell) for the main body. The stem and nozzle will be machined from stainless steel with "spray stelliting" for enhanced wear resistance. The regenerative steam enters at the top of the heater body through a 300 mm diameter inlet port and turns 90 deg. C into the variable nozzle section. This section is adjustable by moving the centre stem towards the tapered nozzle. The slurry enters at the bottom, down stream of the nozzle, into a chamber containing a centrally mounted combining tube for mixing.
The steam from the nozzle is forced down the combining tube with the slurry entering around the circumference. The position of the combining tube is also adjustable to vary the entry area of the slurry.
The design incorporates a series of injection heaters ; Stage 1 raising the temperature of the slurry to 95 deg. C and Stage 2 to 145 deg. C.
The heat necessary to elevate 400 tonnes/hr of the Bauxite slurry from 90 deg. C to 145 deg. C is 12 million KCal/hr. Based on steam at 9.3 bar.a. the required steam flow from Flash Tank 6 is 22 tonnes/hr.
Campo scientifico (EuroSciVoc)
CORDIS classifica i progetti con EuroSciVoc, una tassonomia multilingue dei campi scientifici, attraverso un processo semi-automatico basato su tecniche NLP. Cfr.: Il Vocabolario Scientifico Europeo.
CORDIS classifica i progetti con EuroSciVoc, una tassonomia multilingue dei campi scientifici, attraverso un processo semi-automatico basato su tecniche NLP. Cfr.: Il Vocabolario Scientifico Europeo.
Questo progetto non è ancora stato classificato con EuroSciVoc.
Suggerisci i campi scientifici che ritieni più rilevanti e aiutaci a migliorare il nostro servizio di classificazione.
È necessario effettuare l’accesso o registrarsi per utilizzare questa funzione
Programma(i)
Programmi di finanziamento pluriennali che definiscono le priorità dell’UE in materia di ricerca e innovazione.
Programmi di finanziamento pluriennali che definiscono le priorità dell’UE in materia di ricerca e innovazione.
Argomento(i)
Gli inviti a presentare proposte sono suddivisi per argomenti. Un argomento definisce un’area o un tema specifico per il quale i candidati possono presentare proposte. La descrizione di un argomento comprende il suo ambito specifico e l’impatto previsto del progetto finanziato.
Gli inviti a presentare proposte sono suddivisi per argomenti. Un argomento definisce un’area o un tema specifico per il quale i candidati possono presentare proposte. La descrizione di un argomento comprende il suo ambito specifico e l’impatto previsto del progetto finanziato.
Invito a presentare proposte
Procedura per invitare i candidati a presentare proposte di progetti, con l’obiettivo di ricevere finanziamenti dall’UE.
Dati non disponibili
Procedura per invitare i candidati a presentare proposte di progetti, con l’obiettivo di ricevere finanziamenti dall’UE.
Meccanismo di finanziamento
Meccanismo di finanziamento (o «Tipo di azione») all’interno di un programma con caratteristiche comuni. Specifica: l’ambito di ciò che viene finanziato; il tasso di rimborso; i criteri di valutazione specifici per qualificarsi per il finanziamento; l’uso di forme semplificate di costi come gli importi forfettari.
Meccanismo di finanziamento (o «Tipo di azione») all’interno di un programma con caratteristiche comuni. Specifica: l’ambito di ciò che viene finanziato; il tasso di rimborso; i criteri di valutazione specifici per qualificarsi per il finanziamento; l’uso di forme semplificate di costi come gli importi forfettari.
Coordinatore
CO LIMERICK
Irlanda
I costi totali sostenuti dall’organizzazione per partecipare al progetto, compresi i costi diretti e indiretti. Questo importo è un sottoinsieme del bilancio complessivo del progetto.