Skip to main content
Weiter zur Homepage der Europäischen Kommission (öffnet in neuem Fenster)
Deutsch de
CORDIS - Forschungsergebnisse der EU
CORDIS
Inhalt archiviert am 2022-12-27

USE OF GEOTHERMAL ENERGY TO RUN A 5 MW ELECTRICAL GENERATOR BY TAPPING THE HYDROTHERMAL SYSTEM [STAGE 1]

Ziel

By tapping the latera geothermal field to produce electricity for a 5 Mw generator. Two exploratory boreholes (L1-L2) proved the existence of a productive reservoir:
- steam at 60 t/h - 150 deg C and water at 250 m3/h at 100 deg C. Stage 1 covers the drilling and testing of two production wells between 1,500 and 2,000 m.
The wells are located in the central part of a carbonaceous formation uplifted (Tuscan series). The expected geothermal gradient is 2,7 deg C/10 m.
- Stage II: if the results are positive, two injection wells will be drilled.
- Stage III: this will include the installation and testing of the 5 Mw power plant.
The total annual projected energy saving at the end of the project is 15,000 TOE.
Drilling of wells L3 and L3D verified data obtained from wells L1 and L2 regarding the temperature regime of the caldera and trend of the buried carbonate structure.
Highest temperature gradient value for all Latera zones was recorded at 2,95 deg C/10 m.
Due to lack of permeability in the mesozoic carbonate of the folded structure, well L3 is unproductive. Well L3D (side tracked hole in L3) is highly productive due to fractured layers between 530 and 1,370 m. The proved flow-rate of 600 t/h at 13 Bar and 185 deg C was sufficient to justify initiating the second stage of the project.
The first production well, (L3) was drilled between April and August 1980 to a final depth of 2,485 m. Partly modified limestone and marl (Lias-Trias) was encountered beneath a cover of volcanic strata between 510 and 1,560 m. Rock clays and marls were encountered between 1,560 and 2,300 m, followed by metamorphic formation below 2,300 m. Relatively permeable limestones were traversed between 950 and 1,435. Production is limited to 30 m3/h at a 50 kg/cm2 pressure loss. After injecting water and acid, a reinjection flow-rate of 150 m3/h at 37 bars was obtained. An inversion of the geothermal gradient between 1,000 and 1,700 m suggests the presence of a reservoir close by. With the Commission's agreement, the contractor decided to start directional drilling from the same L3D site instead of going ahead with the planned second production well (L4). This was completed between June and September 1981.
Structural and tectonic factors suggested drilling in the direction of N60E. A 13 3/8" casing was sunk to 520 m drilling continued down to 1,369 m (12 1/4" open hole) through limestone strata, without returns and with several blowouts occurring. One of these - at the reservoir level of around 1,300 m - was spontaneous. Distance between L3D and L3 at 1,300 is 335 m. Drilling continued down to 1,369 m (12 1/4" open hole) through limestone strata, without returns and with several blowouts occuring. Lithological section similar, i.e. Quaternary volcanic strata down to 520 m; Lias limestone from 520 m to 765 m and Upper Lias Limestone from 765 m to 1,369 m. A series of tests (production and reinjection) has been conducted. Principal characteristics revealed by the most recent at 120 t/h (20 % steam, limited by the separator): well-head temperature and pressure - 198 deg C at 18 bars salinity - 20 g/l; temperature at the bottom of the hole - 225 deg C; enthalpy - 231 kcal/kg (pressure loss: 6 bars). It is reasonable to expect a maximun stabilized flow-rate of approximately 600 t/h at 13 bars and 185 deg C without tubing between 520 and 1,369 m, and with 1,5% CO2/HO2 by weight. Drilling of wells L3 and L3D was completed in September 1981.

Wissenschaftliches Gebiet (EuroSciVoc)

CORDIS klassifiziert Projekte mit EuroSciVoc, einer mehrsprachigen Taxonomie der Wissenschaftsbereiche, durch einen halbautomatischen Prozess, der auf Verfahren der Verarbeitung natürlicher Sprache beruht. Siehe: Das European Science Vocabulary.

Dieses Projekt wurde noch nicht bei EuroSciVoc klassifiziert.
Schlagen Sie die Wissenschaftsbereiche vor, die Ihrer Einschätzung nach besonders relevant sind, und helfen Sie uns, unseren Klassifizierungsdienst zu verbessern.

Sie müssen sich anmelden oder registrieren, um diese Funktion zu nutzen

Programm/Programme

Mehrjährige Finanzierungsprogramme, in denen die Prioritäten der EU für Forschung und Innovation festgelegt sind.

Thema/Themen

Aufforderungen zur Einreichung von Vorschlägen sind nach Themen gegliedert. Ein Thema definiert einen bestimmten Bereich oder ein Gebiet, zu dem Vorschläge eingereicht werden können. Die Beschreibung eines Themas umfasst seinen spezifischen Umfang und die erwarteten Auswirkungen des finanzierten Projekts.

Aufforderung zur Vorschlagseinreichung

Verfahren zur Aufforderung zur Einreichung von Projektvorschlägen mit dem Ziel, eine EU-Finanzierung zu erhalten.

Daten nicht verfügbar

Finanzierungsplan

Finanzierungsregelung (oder „Art der Maßnahme“) innerhalb eines Programms mit gemeinsamen Merkmalen. Sieht folgendes vor: den Umfang der finanzierten Maßnahmen, den Erstattungssatz, spezifische Bewertungskriterien für die Finanzierung und die Verwendung vereinfachter Kostenformen wie Pauschalbeträge.

DEM - Demonstration contracts

Koordinator

ENEL SPA
EU-Beitrag
Keine Daten
Adresse
Viale Regina Margherita, 137
00198 ROMA
Italien

Auf der Karte ansehen

Gesamtkosten

Die Gesamtkosten, die dieser Organisation durch die Beteiligung am Projekt entstanden sind, einschließlich der direkten und indirekten Kosten. Dieser Betrag ist Teil des Gesamtbudgets des Projekts.

Keine Daten
Mein Booklet 0 0