Obiettivo
Development of a 1kW internal reforming fuel cell unit. The main problem is the development of reformer catalysts (needed as the available heat is 600-650 C and the heat required for the reaction is 800 C) which are not poisoned by the corrosive carbonate atmosphere.
Catalyst deactivation:
Out-of-cell tests were performed in a tubular reactor to screen a number of potential catalysts as to their suitability for this particular application. From these tests, three catalysts were selected for in-cell tests on 100 cm{2} scale under severe conditions, meaning that the cell was loaded with only a very small amount of catalyst while nominally operated.
By comparing the deactivation rates in these tests, the best catalyst was then tested over 5000 hours under standard MCFC conditions in a 100 cm{2} cell at the end of the project. During that time, its deactivation was found to be negligible. It must be stressed, however, that this holds only for this kind of tests and for these operating times. For longer operation times or for cells eg loaded with a smaller amount of catalyst, deactivation may remain a problem, to which attention must be paid.
Carbonate poisoning:
This was considered to be the main cause of catalyst deactivation and dedicated experiments were performed to investigate the mechanism by which the carbonate was transported to the catalyst. In an MCFC stack, this was found to be either by creep or vapour phase transport. Both mechanisms and their relation with, among others, the catalyst substrate material have been investigated.
Stack testing:
In one of the two short stack experiments, the separator plates were loaded with a pulverized version of one of the selected catalysts (not the one selected for the long-duration test). However, the catalyst loading proved insufficient and the separator plates had to be modified to increase the catalyst loading by incorporating the catalyst in its usual form of 3.2x3.2 mm pellets. Finally, the 1 kW stack test was performed using the modified separator plates. It showed that the required power density (100 mW/cm{2}) could be attained.
Molten carbonate fuel cells (MCFC) operate at 650 C and can produce electricity from methane with 60% efficiency. They use reformers to transform methane into hydrogen for which temperatures of 800 C are required. The hydrogen is then fed into the fuel cell to produce electricity. In this project a concept will be developed where reforming takes place in the fuel cell using its waste heat. In this way the cost can be reduced as an expensive external reformer is not required; additional cost reductions are possible due to lower cooling requirements and the efficiency may be higher than for MCFC which use external reformers.
British Gas and CNR-TAE will develop suitable reformer catalysts. Components, cells up to 1000 cm2 and stacks up to 1 kW will be made by ECN. The testing of cells and stacks will be carried out by ECN.
Campo scientifico (EuroSciVoc)
CORDIS classifica i progetti con EuroSciVoc, una tassonomia multilingue dei campi scientifici, attraverso un processo semi-automatico basato su tecniche NLP. Cfr.: Il Vocabolario Scientifico Europeo.
CORDIS classifica i progetti con EuroSciVoc, una tassonomia multilingue dei campi scientifici, attraverso un processo semi-automatico basato su tecniche NLP. Cfr.: Il Vocabolario Scientifico Europeo.
- scienze naturali scienze chimiche chimica inorganica composti inorganici
- scienze naturali scienze chimiche catalisi
- scienze naturali scienze chimiche chimica organica composti alifatici
- ingegneria e tecnologia ingegneria ambientale energia e carburanti pile a combustibile
È necessario effettuare l’accesso o registrarsi per utilizzare questa funzione
Programma(i)
Programmi di finanziamento pluriennali che definiscono le priorità dell’UE in materia di ricerca e innovazione.
Programmi di finanziamento pluriennali che definiscono le priorità dell’UE in materia di ricerca e innovazione.
Argomento(i)
Gli inviti a presentare proposte sono suddivisi per argomenti. Un argomento definisce un’area o un tema specifico per il quale i candidati possono presentare proposte. La descrizione di un argomento comprende il suo ambito specifico e l’impatto previsto del progetto finanziato.
Dati non disponibili
Gli inviti a presentare proposte sono suddivisi per argomenti. Un argomento definisce un’area o un tema specifico per il quale i candidati possono presentare proposte. La descrizione di un argomento comprende il suo ambito specifico e l’impatto previsto del progetto finanziato.
Invito a presentare proposte
Procedura per invitare i candidati a presentare proposte di progetti, con l’obiettivo di ricevere finanziamenti dall’UE.
Dati non disponibili
Procedura per invitare i candidati a presentare proposte di progetti, con l’obiettivo di ricevere finanziamenti dall’UE.
Meccanismo di finanziamento
Meccanismo di finanziamento (o «Tipo di azione») all’interno di un programma con caratteristiche comuni. Specifica: l’ambito di ciò che viene finanziato; il tasso di rimborso; i criteri di valutazione specifici per qualificarsi per il finanziamento; l’uso di forme semplificate di costi come gli importi forfettari.
Meccanismo di finanziamento (o «Tipo di azione») all’interno di un programma con caratteristiche comuni. Specifica: l’ambito di ciò che viene finanziato; il tasso di rimborso; i criteri di valutazione specifici per qualificarsi per il finanziamento; l’uso di forme semplificate di costi come gli importi forfettari.
Coordinatore
1755 ZG PETTEN
Paesi Bassi
I costi totali sostenuti dall’organizzazione per partecipare al progetto, compresi i costi diretti e indiretti. Questo importo è un sottoinsieme del bilancio complessivo del progetto.