Clean and efficient microCHCP by micro turbine based hybrid systems

Informations projet

Fit4Micro

N° de convention de subvention: 101083536

DOI

10.3030/101083536

Date de signature de la CE 23 Août 2022

Date de début 1 Octobre 2022

Date de fin 30 Septembre 2026

Financé au titre de

• Climate, Energy and Mobility

Coût total

€ 4 993 387,50

Contribution de l’UE

€ 4 993 387,50

Coordonné par

MITIS
Belgium

CORDIS fournit des liens vers les livrables publics et les publications des projets HORIZON.

Les liens vers les livrables et les publications des projets du 7e PC, ainsi que les liens vers certains types de résultats spécifiques tels que les jeux de données et les logiciels, sont récupérés dynamiquement sur OpenAIRE .

Livrables

Data Management Plan (1)

Data Management Plan (DMP)

The DMP outlines what data will be generated and collected, the used methodology and standards for data collection and describes how the research data is made available during the project as well as preserved after completion of the project.Linked to Task 8.2

Documents, reports (5)

Dissemination, Exploitation and Communication plan 1

The plan will contain the following elements 1 identification of specific target groups and a mapping of key stakeholders at EU and at national level for project outreach and dissemination 2 the initial key messages and information relevant for each target group 3 the tools and channels that will be used to convey the messages and the information to each target group 4 schedule of activities until M18Linked to Task 82

Production report of 200 L reference-quality HPO

Production report of 200 L reference-quality HPO, describing the used feedstock, the applied operating conditions and final product specifications based on analysis results.Linked to Task 2.1

Dissemination, Exploitation and Communication plan 2

Revision of the original plan, updating the schedule of activities until M36Linked to Task 8.2

Operating parameters combustor

The first step in the development of the combustor is to characterize operating parameters and requirements eg fuel and air supply operating pressure relevant temperatures These parameters will be documented and regularly updated based on the gained experience of the system Deliverable is linked to task 31Linked to Task 31

Report on 4 use case definitions for system development and evaluations

Report on 4 use case definitions for system development and evaluations: At least 4 use cases will be defined (heating and/or cooling demands, climate zone, building types), which will then be used for system development and evaluation of potential.Linked to Task 5.1

Publications

Conference proceedings (2)

Humidification Impact on the Performance Improvement of a Novel Two-Shaft Micro Gas Turbine: Thermodynamic Cycle Performance Assessment

Auteurs: Ali Baghernejad, Danish Rehman, Michel Delanaye, Ward De Paepe
Publié dans: Volume 5: Cycle Innovations, 2024
Éditeur: American Society of Mechanical Engineers
DOI: 10.1115/GT2024-128549

Clean and efficient microCHCP by micro turbine-based hybrid systems: The Fit4Micro project

Auteurs: Delanaye, M., Rehman D, Bjorn Aaen S, Lokke S, Leijenhorst E, Van de Beld B, Korteweg H, Tudoroiu A, Baghernejead A, De Paepe W, Hermann R, Nonnen T, Velte A, Fuldner G, Ramaswamy S, Harboe-Minwegen S, Ridolfi T, Capaccioli S
Publié dans: European Biomass Conference and Exhibition Proceedings, 2023, ISSN 2282-5819
Éditeur: ETA Florence Renewable Energies
DOI: 10.5071/31STEUBCE2023-3CV.4.10

Peer reviewed articles (1)

Optimal waste heat recovery through humidification in 2-spool micro gas turbines: A comparative study of advanced humidified cycles

Auteurs: Aggelos Gaitanis; Francesco Contino; Ward De Paepe
Publié dans: Energy, 2025, ISSN 1873-6785
Éditeur: Elsevier
DOI: 10.2139/SSRN.5087255