Clean and efficient microCHCP by micro turbine based hybrid systems

Projektinformationen

Fit4Micro

ID Finanzhilfevereinbarung: 101083536

DOI

10.3030/101083536

EK-Unterschriftsdatum 23 August 2022

Startdatum 1 Oktober 2022

Enddatum 30 September 2026

Finanziert unter

• Climate, Energy and Mobility

Gesamtkosten

€ 4 993 387,50

EU-Beitrag

€ 4 993 387,50

Koordiniert durch

MITIS
Belgium

CORDIS bietet Links zu öffentlichen Ergebnissen und Veröffentlichungen von HORIZONT-Projekten.

Links zu Ergebnissen und Veröffentlichungen von RP7-Projekten sowie Links zu einigen Typen spezifischer Ergebnisse wie Datensätzen und Software werden dynamisch von OpenAIRE abgerufen.

Leistungen

Data Management Plan (1)

Data Management Plan (DMP)

The DMP outlines what data will be generated and collected, the used methodology and standards for data collection and describes how the research data is made available during the project as well as preserved after completion of the project.Linked to Task 8.2

Documents, reports (5)

Dissemination, Exploitation and Communication plan 1

The plan will contain the following elements 1 identification of specific target groups and a mapping of key stakeholders at EU and at national level for project outreach and dissemination 2 the initial key messages and information relevant for each target group 3 the tools and channels that will be used to convey the messages and the information to each target group 4 schedule of activities until M18Linked to Task 82

Production report of 200 L reference-quality HPO

Production report of 200 L reference-quality HPO, describing the used feedstock, the applied operating conditions and final product specifications based on analysis results.Linked to Task 2.1

Dissemination, Exploitation and Communication plan 2

Revision of the original plan, updating the schedule of activities until M36Linked to Task 8.2

Operating parameters combustor

The first step in the development of the combustor is to characterize operating parameters and requirements eg fuel and air supply operating pressure relevant temperatures These parameters will be documented and regularly updated based on the gained experience of the system Deliverable is linked to task 31Linked to Task 31

Report on 4 use case definitions for system development and evaluations

Report on 4 use case definitions for system development and evaluations: At least 4 use cases will be defined (heating and/or cooling demands, climate zone, building types), which will then be used for system development and evaluation of potential.Linked to Task 5.1

Veröffentlichungen

Conference proceedings (6)

NOx Reduction Through Swirl Injector for Hydrogen and Methane Combustion in Mild Conditions

Autoren: Jojomon Joseph, Mahdi Jamshidiha, Danish Rehman, Axel Coussement, Alessandro Parente, Michel Delanaye
Veröffentlicht in: Volume 7: Manufacturing Materials & Metallurgy; Microturbines, Turbochargers & Small Turbomachines; Oil & Gas Applications; Steam Turbine; Structures and Dynamics: Aerodynamics Excitation & Damping, 2025
Herausgeber: American Society of Mechanical Engineers
DOI: 10.1115/GT2025-154188

Humidification Impact on the Performance Improvement of a Novel Two-Shaft Micro Gas Turbine: Thermodynamic Cycle Performance Assessment

Autoren: Ali Baghernejad, Danish Rehman, Michel Delanaye, Ward De Paepe
Veröffentlicht in: Volume 5: Cycle Innovations, 2024
Herausgeber: American Society of Mechanical Engineers
DOI: 10.1115/GT2024-128549

Clean and efficient microCHCP by micro turbine-based hybrid systems: The Fit4Micro project

Autoren: Delanaye, M., Rehman D, Bjorn Aaen S, Lokke S, Leijenhorst E, Van de Beld B, Korteweg H, Tudoroiu A, Baghernejead A, De Paepe W, Hermann R, Nonnen T, Velte A, Fuldner G, Ramaswamy S, Harboe-Minwegen S, Ridolfi T, Capaccioli S
Veröffentlicht in: European Biomass Conference and Exhibition Proceedings, 2023, ISSN 2282-5819
Herausgeber: ETA Florence Renewable Energies
DOI: 10.5071/31STEUBCE2023-3CV.4.10

Dynamic Modeling and Experimental Insights in a 10 kWe Micro Gas Turbine Prototype: Experimental Validation and Testing

Autoren: Aggelos Gaitanis, Martin Heylen, Sophie Mullender, Ward De Paepe
Veröffentlicht in: Volume 4: Controls, Diagnostics & Instrumentation; Cycle Innovations; Education; Electric Power, 2025
Herausgeber: American Society of Mechanical Engineers
DOI: 10.1115/GT2025-153032

Fit4Micro Solution for a MicroCHCP Hybrid Heating System Running on Biofuels

Autoren: Capaccioli, S., Delanaye, M., Rehman, D., Løkke, S., Leijenhorst, E., van de Beld, B., Korteweg, H., Tudoroiu, A., De Paepe, W., Füldner, G., Harboe-Minwegen, S.
Veröffentlicht in: EUBCE 2025 Proceedings, Ausgabe 1, 2025, ISBN 978-88-89407-25-7
Herausgeber: ETA-Florence Renewable Energies

Experimental Investigation of Structural Characteristics and Viscous Energy Dissipation in Multiple Cantilever Gas Foil Radial Bearings

Autoren: Danish Rehman, Michel Delanaye
Veröffentlicht in: Volume 8: Structures and Dynamics — Bearing & Seal Dynamics; Emerging Methods in Engineering Design, Analysis and Additive Manufacturing; Fatigue, Fracture & Life Prediction; Probabilistic Methods; Rotordynamics, 2025
Herausgeber: American Society of Mechanical Engineers
DOI: 10.1115/GT2025-153247

Peer reviewed articles (1)

Optimal waste heat recovery through humidification in 2-spool micro gas turbines: A comparative study of advanced humidified cycles

Autoren: Aggelos Gaitanis; Francesco Contino; Ward De Paepe
Veröffentlicht in: Energy, Ausgabe 332, 2025, ISSN 1873-6785
Herausgeber: Elsevier
DOI: 10.1016/J.ENERGY.2025.136976