Pilot line for European Production of PEROvskite-Silicon taNdem modules on Industrial scale

Informazioni relative al progetto

PEPPERONI

ID dell’accordo di sovvenzione: 101084251

DOI

10.3030/101084251

Data della firma CE 20 Ottobre 2022

Data di avvio 1 Novembre 2022

Data di completamento 31 Ottobre 2026

Finanziato da

• Climate, Energy and Mobility

Costo totale

€ 17 020 325,00

Contributo UE

€ 12 950 825,00

Coordinato da

HELMHOLTZ-ZENTRUM BERLIN FUR MATERIALIEN UND ENERGIE GMBH
Germany

Periodic Reporting for period 1 - PEPPERONI (Pilot line for European Production of PEROvskite-Silicon taNdem modules on Industrial scale)

Periodo di rendicontazione: 2022-11-01 al 2024-04-30

Sintesi del contesto e degli obiettivi generali del progetto

Europe is facing the challenge of making its energy system clean, secure and efficient, while ensuring industrial leadership in low-carbon energy technologies. The EU has ambitious goals to tackle the ongoing climate crisis and targets climate neutrality by 2050. Photovoltaic (PV) power generation is pivotal in this transition and the achievement of the zero-emission target.

PEPPERONI was set up to support Europe in reaching its renewable energy targets. PEPPERONI will help advance perovskite/silicon tandem photovoltaics (PV) technology’s journey towards the market introduction and mass manufacturing.

The project will identify and address the barriers to tandem solar technology’s market introduction, and ultimately lay the foundations for fast implementation of new production capacity in Europe as a cost-effective and resource-efficient solution to decarbonise the energy system.

A pilot line enabling this development will be established in Thalheim, Germany, with the long-term vision of enabling European industrial leadership on PV production in the global market.

Lavoro eseguito dall’inizio del progetto fino alla fine del periodo coperto dalla relazione e principali risultati finora ottenuti

The first 18 months of the project have been mainly focusing on equipment installation and adaptation as well as developing manufacturing processes to produce perovskite/silicon tandem solar cells in laboratory and pilot line environments.

At the cell level, different approaches to deposit the perovskite absorber are being investigated and benchmarked by analysing the optoelectronic quality of the perovskite film, the efficiency achievable with small-scale tandem prototypes, the scalability of the process to full-size industrial Si wafers, and the applicability of the processes and associated equipment for an industrial production environment.

At the module level, the consortium has been investigating the interconnection of cells into strings and their lamination to produce modules, achieving the cell-to-module loss target defined in the project for small-scale prototypes. For this purpose, a screening of encapsulation materials has been performed. Then, encapsulated tandem solar cells have been exposed to various stability test conditions (thermal cycling, damp heat, light soaking at elevated temperature) to identify the most stable combination of materials. In addition, the outdoor monitoring of small-area tandem prototypes has also begun.

At the pilot line level, processing equipment has been installed and industrial process flows to produce tandem cells are being established. Equipment for the interconnection and encapsulation is being adapted for the application of perovskite/Si tandem module processing. Life cycle assessment and societal impact studies have also commenced.

Progressi oltre lo stato dell’arte e potenziale impatto previsto (incluso l’impatto socioeconomico e le implicazioni sociali più ampie del progetto fino ad ora)

Key results achieved so far include the implementation and operation of equipment and processes to produce M10-wafer size perovskite/Si tandem solar cells and first full-size prototype modules. To the best of our knowledge, there has been no public demonstration of functional M10 perovskite/Si tandem solar cells, let alone industrial-size functional perovskite/Si modules based on M10 format cells. Other key results include the development and benchmarking of materials and processes for industrial manufacturing of perovskite/Si tandem solar cells and modules, and the demonstration of small-scale encapsulated tandem solar cells passing the IEC 61215 damp heat and thermal cycling test criteria. As one of the most challenging processes, the upscaling of perovskite absorber deposition is being tackled by various methods and multiple partners. While currently most tandem cells from literature are manufactured by spin-coating (solution-based process) the perovskite absorber and other functional layers, this approach is not scalable and therefore not viable for industrial application. In contrast, in Pepperoni we focus on scalable methods. Initial small-area tandem cells fabricated with scalable methods and using Qcells bottom cells employing state-of-the-art industrial manufacturing technology already show very promising performance beyond the state-of-the-art.

Logo of the PEPPERONI project