Periodic Reporting for period 1 - Spec4DeSal (Transforming Interface Studies for Sustainable Desalination: The Development of Interface-Specific Heterodyne-Detected χ(4) Spectroscopy for the study of Molybdenum Disulfide Nanochannels)
Berichtszeitraum: 2024-04-01 bis 2026-06-30
Zusammenfassung vom Kontext und den Gesamtzielen des Projekts
Access to clean drinking water is one of the major global challenges of the twenty first century. Although water covers most of the Earth’s surface, only a very small fraction is directly suitable for drinking. At the same time, population growth, climate change, drought, and desertification are increasing pressure on freshwater resources. These pressures are not limited to one region. Water scarcity already affects many communities worldwide and is expected to become more severe in the coming decades. New technologies are therefore needed to produce clean water in a way that is efficient, affordable, and environmentally sustainable.
Seawater desalination is one promising route to address this challenge, but many established desalination technologies require large energy inputs. This limits their wider use and can increase costs and environmental impact. A major scientific and technological need is therefore to develop desalination approaches that use less energy while maintaining high performance. Interfacial solar vapour generation is one such approach. Instead of heating a large volume of water, it uses sunlight absorbing materials to localise heat at the water surface, where evaporation occurs. This can improve energy efficiency and may offer a route toward more sustainable water purification.
Two dimensional materials, such as molybdenum disulfide, are especially promising for this purpose. Molybdenum disulfide can form nanoscale channels that interact with water and absorb solar energy. These nanochannels have potential for improving solar driven desalination, but the molecular details of how water behaves inside and near these channels remain insufficiently understood. This knowledge gap limits the rational design of better desalination materials. To improve performance, researchers need to understand how water molecules are arranged, how they move, and how salts and channel properties influence these interfacial processes.
The overall objective of this project is to develop and apply an advanced laser based spectroscopy method to study water at buried material interfaces relevant to desalination. The project will develop a heterodyne detected fourth order sum frequency generation spectroscopy platform. This method is designed to probe interfaces that are difficult to access with existing techniques, especially water solid interfaces hidden beneath water layers. Unlike conventional approaches, the method aims to provide phase sensitive molecular information, allowing more reliable conclusions about the orientation and structure of interfacial water.
The project follows three main objectives. First, a new spectrometer will be constructed and optimised using ultrafast laser sources. Second, the method will be applied to study water at molybdenum disulfide surfaces and then within molybdenum disulfide nanochannels. Third, the experimental spectra will be analysed together with molecular simulations and electronic structure calculations to extract molecular level insight into the interface. These results will help identify how channel structure, salt concentration, and interfacial water organisation influence desalination relevant performance.
The pathway to impact is based on linking fundamental molecular knowledge to materials design. By revealing how water behaves in molybdenum disulfide nanochannels, the project can provide design principles for improved solar vapour generation materials. These insights can support the development of more efficient desalination systems, contributing to clean water access and more sustainable water treatment technologies. The new spectroscopic method is also expected to have broader scientific and technological value. Many important systems in energy, electrochemistry, batteries, catalysis, and environmental science involve buried liquid solid interfaces that are difficult to study directly. A successful method could therefore open new possibilities for studying and optimising a wide range of interfacial technologies.
The expected impact is scientific, technological, and societal. Scientifically, the project will advance understanding of interfacial water structure and dynamics in nanoscale materials. Technologically, it will provide a new measurement platform for buried interfaces and generate knowledge that can support improved desalination materials. Societally, it contributes to the long term goal of more sustainable access to clean water, which is closely aligned with European and global priorities on climate resilience, resource efficiency, and sustainable development. The project is therefore positioned to address an urgent global need while also strengthening Europe’s capacity in advanced spectroscopy, materials science, and sustainable water technologies.
Seawater desalination is one promising route to address this challenge, but many established desalination technologies require large energy inputs. This limits their wider use and can increase costs and environmental impact. A major scientific and technological need is therefore to develop desalination approaches that use less energy while maintaining high performance. Interfacial solar vapour generation is one such approach. Instead of heating a large volume of water, it uses sunlight absorbing materials to localise heat at the water surface, where evaporation occurs. This can improve energy efficiency and may offer a route toward more sustainable water purification.
Two dimensional materials, such as molybdenum disulfide, are especially promising for this purpose. Molybdenum disulfide can form nanoscale channels that interact with water and absorb solar energy. These nanochannels have potential for improving solar driven desalination, but the molecular details of how water behaves inside and near these channels remain insufficiently understood. This knowledge gap limits the rational design of better desalination materials. To improve performance, researchers need to understand how water molecules are arranged, how they move, and how salts and channel properties influence these interfacial processes.
The overall objective of this project is to develop and apply an advanced laser based spectroscopy method to study water at buried material interfaces relevant to desalination. The project will develop a heterodyne detected fourth order sum frequency generation spectroscopy platform. This method is designed to probe interfaces that are difficult to access with existing techniques, especially water solid interfaces hidden beneath water layers. Unlike conventional approaches, the method aims to provide phase sensitive molecular information, allowing more reliable conclusions about the orientation and structure of interfacial water.
The project follows three main objectives. First, a new spectrometer will be constructed and optimised using ultrafast laser sources. Second, the method will be applied to study water at molybdenum disulfide surfaces and then within molybdenum disulfide nanochannels. Third, the experimental spectra will be analysed together with molecular simulations and electronic structure calculations to extract molecular level insight into the interface. These results will help identify how channel structure, salt concentration, and interfacial water organisation influence desalination relevant performance.
The pathway to impact is based on linking fundamental molecular knowledge to materials design. By revealing how water behaves in molybdenum disulfide nanochannels, the project can provide design principles for improved solar vapour generation materials. These insights can support the development of more efficient desalination systems, contributing to clean water access and more sustainable water treatment technologies. The new spectroscopic method is also expected to have broader scientific and technological value. Many important systems in energy, electrochemistry, batteries, catalysis, and environmental science involve buried liquid solid interfaces that are difficult to study directly. A successful method could therefore open new possibilities for studying and optimising a wide range of interfacial technologies.
The expected impact is scientific, technological, and societal. Scientifically, the project will advance understanding of interfacial water structure and dynamics in nanoscale materials. Technologically, it will provide a new measurement platform for buried interfaces and generate knowledge that can support improved desalination materials. Societally, it contributes to the long term goal of more sustainable access to clean water, which is closely aligned with European and global priorities on climate resilience, resource efficiency, and sustainable development. The project is therefore positioned to address an urgent global need while also strengthening Europe’s capacity in advanced spectroscopy, materials science, and sustainable water technologies.
Arbeit, die ab Beginn des Projekts bis zum Ende des durch den Bericht erfassten Berichtszeitraums geleistet wurde, und die wichtigsten bis dahin erzielten Ergebnisse
The project focused on developing advanced nonlinear optical spectroscopy for studying aqueous interfaces at the molecular level. During the project, the original technical direction evolved from the direct implementation of fourth order spectroscopy toward the development of a more broadly applicable and experimentally robust ultrafast spectroscopy platform. This shift was scientifically justified because the construction of a stable, flexible, and high performance light source is a necessary foundation for future measurements of complex buried interfaces, while also enabling immediate studies of charged interfaces and aqueous electrolytes.
A major technical achievement was the design, construction, and optimisation of a novel optical parametric amplifier. This source was developed to generate tunable ultrafast pulses suitable for nonlinear spectroscopic measurements of aqueous interfaces. Considerable work was devoted to white light generation, pump beam preparation, nonlinear crystal alignment, pulse timing, wavelength tuning, beam stability, and spectral characterisation. The resulting optical parametric amplifier provided the tunability, stability, and pulse properties required to drive a new generation of heterodyne detected sum frequency generation experiments.
This optical source was then integrated into a custom built heterodyne detected sum frequency generation platform. The instrument is unusual because it is capable of performing sum frequency generation measurements using two different visible wavelength configurations, while also enabling difference frequency generation measurements. This makes the setup highly flexible for probing different spectral regions and for adapting the experiment to different interfacial systems. The system was developed as a largely collinear optical design, which simplifies spatial overlap, improves long term stability, and provides a compact and adaptable route for nonlinear optical measurements. To the best of our knowledge, this represents one of the first implementations of this type of collinear, multi modality heterodyne detected SFG/DFG platform.
A substantial part of the work involved establishing the optical, mechanical, and detection infrastructure required for reliable phase sensitive spectroscopy. This included the generation and control of the local oscillator, the optimisation of beam overlap at the sample, the implementation of timing control between pulses, and the development of acquisition and analysis routines for extracting heterodyne detected spectra. Reference measurements were used to test the stability, phase sensitivity, and reproducibility of the system. These developments transformed the project from a single target measurement into a versatile platform for studying a broad range of interfacial water systems.
Using this new capability, several scientific studies were performed on charged aqueous interfaces and aqueous electrolyte systems. These studies focused on how ions, surface charge, and interfacial electric fields influence the structure and orientation of water at interfaces. Heterodyne detected SFG measurements provided phase sensitive information on the hydrogen bonded water network, allowing changes in interfacial water organisation to be followed as a function of electrolyte composition and concentration. The work contributed to a more detailed molecular picture of how charged interfaces interact with water and dissolved ions.
The experimental studies also helped establish the broader value of the new instrument. Charged interfaces and electrolytes are central to many processes in chemistry, energy conversion, electrochemistry, colloid science, environmental chemistry, and membrane science. By providing direct spectroscopic access to interfacial water structure, the new setup enables questions to be addressed that are difficult to resolve using conventional bulk sensitive methods. The ability to combine different wavelength configurations and DFG capability further expands the range of systems and vibrational modes that can be studied.
The main achievements of the project were therefore technical and scientific. Technically, the project delivered a novel optical parametric amplifier and a one of a kind heterodyne detected SFG/DFG platform with dual wavelength SFG capability and a collinear design. Scientifically, the project used this platform to investigate charged aqueous interfaces and electrolyte dependent interfacial water structure. Together, these outcomes provide a strong foundation for future studies of complex liquid solid interfaces, confined water, electrochemical systems, and materials relevant to sustainable water technologies.
A major technical achievement was the design, construction, and optimisation of a novel optical parametric amplifier. This source was developed to generate tunable ultrafast pulses suitable for nonlinear spectroscopic measurements of aqueous interfaces. Considerable work was devoted to white light generation, pump beam preparation, nonlinear crystal alignment, pulse timing, wavelength tuning, beam stability, and spectral characterisation. The resulting optical parametric amplifier provided the tunability, stability, and pulse properties required to drive a new generation of heterodyne detected sum frequency generation experiments.
This optical source was then integrated into a custom built heterodyne detected sum frequency generation platform. The instrument is unusual because it is capable of performing sum frequency generation measurements using two different visible wavelength configurations, while also enabling difference frequency generation measurements. This makes the setup highly flexible for probing different spectral regions and for adapting the experiment to different interfacial systems. The system was developed as a largely collinear optical design, which simplifies spatial overlap, improves long term stability, and provides a compact and adaptable route for nonlinear optical measurements. To the best of our knowledge, this represents one of the first implementations of this type of collinear, multi modality heterodyne detected SFG/DFG platform.
A substantial part of the work involved establishing the optical, mechanical, and detection infrastructure required for reliable phase sensitive spectroscopy. This included the generation and control of the local oscillator, the optimisation of beam overlap at the sample, the implementation of timing control between pulses, and the development of acquisition and analysis routines for extracting heterodyne detected spectra. Reference measurements were used to test the stability, phase sensitivity, and reproducibility of the system. These developments transformed the project from a single target measurement into a versatile platform for studying a broad range of interfacial water systems.
Using this new capability, several scientific studies were performed on charged aqueous interfaces and aqueous electrolyte systems. These studies focused on how ions, surface charge, and interfacial electric fields influence the structure and orientation of water at interfaces. Heterodyne detected SFG measurements provided phase sensitive information on the hydrogen bonded water network, allowing changes in interfacial water organisation to be followed as a function of electrolyte composition and concentration. The work contributed to a more detailed molecular picture of how charged interfaces interact with water and dissolved ions.
The experimental studies also helped establish the broader value of the new instrument. Charged interfaces and electrolytes are central to many processes in chemistry, energy conversion, electrochemistry, colloid science, environmental chemistry, and membrane science. By providing direct spectroscopic access to interfacial water structure, the new setup enables questions to be addressed that are difficult to resolve using conventional bulk sensitive methods. The ability to combine different wavelength configurations and DFG capability further expands the range of systems and vibrational modes that can be studied.
The main achievements of the project were therefore technical and scientific. Technically, the project delivered a novel optical parametric amplifier and a one of a kind heterodyne detected SFG/DFG platform with dual wavelength SFG capability and a collinear design. Scientifically, the project used this platform to investigate charged aqueous interfaces and electrolyte dependent interfacial water structure. Together, these outcomes provide a strong foundation for future studies of complex liquid solid interfaces, confined water, electrochemical systems, and materials relevant to sustainable water technologies.
Fortschritte, die über den aktuellen Stand der Technik hinausgehen und voraussichtliche potenzielle Auswirkungen (einschließlich der bis dato erzielten sozioökonomischen Auswirkungen und weiter gefassten gesellschaftlichen Auswirkungen des Projekts)
The project delivered results beyond the state of the art in both instrumentation and molecular level interface science. The central achievement was the development of a novel ultrafast optical parametric amplifier and its integration into a custom heterodyne detected nonlinear spectroscopy platform. This new platform enables phase sensitive sum frequency generation measurements using two different visible wavelength configurations and also supports difference frequency generation. The instrument therefore provides a flexible route to probe aqueous interfaces over multiple spectral windows with high sensitivity and molecular specificity.
A key advance is the largely collinear optical design of the system. Most heterodyne detected sum frequency generation instruments rely on noncollinear beam geometries, which can make beam overlap, long term stability, and future expansion technically demanding. The collinear design developed in this project simplifies spatial overlap of the beams, improves mechanical and optical stability, and provides a compact architecture for advanced nonlinear spectroscopy. This makes the system one of the first designs of its kind for combined heterodyne detected SFG and DFG measurements. The result is not only a working instrument, but also a new experimental framework that can be adapted to a wide range of interfacial systems.
The optical parametric amplifier developed during the project is another important result beyond the state of the art. It provides tunable ultrafast pulses suitable for driving multiple nonlinear optical processes. Its development required optimisation of white light generation, nonlinear amplification, wavelength selection, beam quality, pulse timing, and output stability. This source is central to the flexibility of the final instrument and provides a foundation for future experiments that require precise control over wavelength, pulse energy, and timing.
The scientific work performed with the new platform focused on charged aqueous interfaces and aqueous electrolyte systems. These systems are important because interfacial charge, ions, and water structure govern many processes in electrochemistry, colloid science, membranes, environmental chemistry, and water purification. The heterodyne detected SFG measurements provided phase sensitive information about the hydrogen bonded water network at charged interfaces. This allowed changes in water orientation and interfacial organisation to be followed as a function of electrolyte conditions. These results contribute to a more detailed molecular understanding of how ions and electric fields influence aqueous interfaces.
The project therefore advanced beyond the state of the art in two linked ways. First, it established a one of a kind nonlinear optical platform with dual wavelength SFG capability, DFG capability, and a collinear heterodyne detected geometry. Second, it used this platform to generate new insight into the molecular structure of charged aqueous interfaces. Together, these results provide a stronger experimental basis for studying complex liquid interfaces, including systems relevant to desalination, electrochemistry, catalysis, membranes, and energy materials.
The potential impact of the results is broad. Scientifically, the instrument enables more flexible and reliable studies of interfacial water, ions, and electric fields. Technologically, the platform can support the future design and characterisation of materials for water treatment, energy conversion, and electrochemical devices. The ability to perform both SFG and DFG measurements expands the range of vibrational modes and interfacial environments that can be accessed. This is particularly important for studying systems where conventional optical geometries or single wavelength approaches are insufficient.
Further uptake and success will require several next steps. Continued research is needed to apply the instrument to a wider range of charged, confined, and buried interfaces. Demonstration studies on technologically relevant materials, such as membranes, electrodes, catalysts, and water purification materials, would help establish the broader value of the platform. Further optimisation of automation, data acquisition, and analysis workflows would improve reproducibility and make the method more accessible to other users. In the longer term, standardised measurement and analysis protocols would support wider adoption by the spectroscopy, materials science, and electrochemistry communities.
The results may also have future exploitation potential. The optical layout, data analysis routines, and combined SFG/DFG capability could be valuable for advanced research laboratories and instrument developers. At this stage, further research and demonstration are the main needs, rather than immediate commercialisation. However, intellectual property support may be useful if specific optical designs, measurement protocols, or software tools prove to be broadly transferable. International collaboration will also be important, because the scientific and technological questions addressed by this platform are relevant across water research, energy materials, and interfacial chemistry.
A key advance is the largely collinear optical design of the system. Most heterodyne detected sum frequency generation instruments rely on noncollinear beam geometries, which can make beam overlap, long term stability, and future expansion technically demanding. The collinear design developed in this project simplifies spatial overlap of the beams, improves mechanical and optical stability, and provides a compact architecture for advanced nonlinear spectroscopy. This makes the system one of the first designs of its kind for combined heterodyne detected SFG and DFG measurements. The result is not only a working instrument, but also a new experimental framework that can be adapted to a wide range of interfacial systems.
The optical parametric amplifier developed during the project is another important result beyond the state of the art. It provides tunable ultrafast pulses suitable for driving multiple nonlinear optical processes. Its development required optimisation of white light generation, nonlinear amplification, wavelength selection, beam quality, pulse timing, and output stability. This source is central to the flexibility of the final instrument and provides a foundation for future experiments that require precise control over wavelength, pulse energy, and timing.
The scientific work performed with the new platform focused on charged aqueous interfaces and aqueous electrolyte systems. These systems are important because interfacial charge, ions, and water structure govern many processes in electrochemistry, colloid science, membranes, environmental chemistry, and water purification. The heterodyne detected SFG measurements provided phase sensitive information about the hydrogen bonded water network at charged interfaces. This allowed changes in water orientation and interfacial organisation to be followed as a function of electrolyte conditions. These results contribute to a more detailed molecular understanding of how ions and electric fields influence aqueous interfaces.
The project therefore advanced beyond the state of the art in two linked ways. First, it established a one of a kind nonlinear optical platform with dual wavelength SFG capability, DFG capability, and a collinear heterodyne detected geometry. Second, it used this platform to generate new insight into the molecular structure of charged aqueous interfaces. Together, these results provide a stronger experimental basis for studying complex liquid interfaces, including systems relevant to desalination, electrochemistry, catalysis, membranes, and energy materials.
The potential impact of the results is broad. Scientifically, the instrument enables more flexible and reliable studies of interfacial water, ions, and electric fields. Technologically, the platform can support the future design and characterisation of materials for water treatment, energy conversion, and electrochemical devices. The ability to perform both SFG and DFG measurements expands the range of vibrational modes and interfacial environments that can be accessed. This is particularly important for studying systems where conventional optical geometries or single wavelength approaches are insufficient.
Further uptake and success will require several next steps. Continued research is needed to apply the instrument to a wider range of charged, confined, and buried interfaces. Demonstration studies on technologically relevant materials, such as membranes, electrodes, catalysts, and water purification materials, would help establish the broader value of the platform. Further optimisation of automation, data acquisition, and analysis workflows would improve reproducibility and make the method more accessible to other users. In the longer term, standardised measurement and analysis protocols would support wider adoption by the spectroscopy, materials science, and electrochemistry communities.
The results may also have future exploitation potential. The optical layout, data analysis routines, and combined SFG/DFG capability could be valuable for advanced research laboratories and instrument developers. At this stage, further research and demonstration are the main needs, rather than immediate commercialisation. However, intellectual property support may be useful if specific optical designs, measurement protocols, or software tools prove to be broadly transferable. International collaboration will also be important, because the scientific and technological questions addressed by this platform are relevant across water research, energy materials, and interfacial chemistry.