Ziel
The objective was to exploit the potential advantages of a significant increase in recording capacity when metallic thin films, instead of conventional oxide particles, are used as the basis for magnetic recording media. In order to develop such a technology, the interdependence of substrate materials, thin magnetic layers, overcoats, heads and drive systems need to be assessed, developed and produced accordingly.
LeyboldHeraeus was responsible for the development of various deposition methods, eg sputtering, evaporation and plasmaCVD for the magnetic layer, while the definition of the quality standards of the disks and their possible implementation into a disk drive system was entrusted, from October1987, to SAGEM, which was also responsible of the evaluation of differently prepared media.
The objective was to exploit the potential advantages of a significant increase in recording capacity when metallic thin films, instead of conventional oxide particles, are used as the basis for magnetic recording media. In order to develop such a technology, the interdependence of substrate materials, thin magnetic layers, overcoats, heads and drive systems need to be assessed, developed and produced accordingly.
Among the different deposition methods, sputtering has reached the most advanced status. A sputtering system, suitable for the study of production conditions, has been designed and built. The machine is a vertical inline system for double sided disk coating and provides the best conditions for continuous production and for a high disk quality with a minimum risk of defects.
Special emphasis has been put on carbon overcoating for mechanical and chemical protection of the recording layer. Complete layer systems were deposited, both in the above mentioned machine on hard disks and in a large roll coater on foils for the industrial production of floppy disks, with promising results.
The work has been focused on hard discs for longitudinal recording and on protective and lubricating layers for use in Winchester drives. The new thin film production technologies developed during these studies can now be used in a future production line, based on the new equipment now available, with the quality and reproducibility needed to market the discs.
Among the different deposition methods, sputtering has reached the most advanced status. At LeyboldHeraeus a sputtering system, suitable for the study of production conditions, has been designed and built. The machine is a vertical in-line system for dou blesided disk coating and provides the best conditions for continuous production and for a high disk quality with a minimum risk of defects. The process technology for the fabrication of disks with longitudinal recording has developed so far that the qua lity can compete with other good quality disks available on the market, but the maximum storage capacity is still expected to be achieved by vertical recording.
Special emphasis has also been put on carbon overcoating for mechanical and chemical protection of the recording layer. Complete layer systems were deposited, both in the above-mentioned machine on hard disks and in a large roll coater on foils for the industrial production of floppy disks, with promising results.
Media studies by the partners clearly demonstrate the potential advantage (a substantial increase in recording capacity) of thin magnetic layers over conventional oxide particles for high-density recording. However, the switchover to thin-film media requ ires many modifications of the standard production technology.
Tribological problems between heads and disc still remain drawbacks in vertical recording. The strong involvement of heads manufacturers is necessary to overcome these problems and to define the needed standard heads and the consequent media characteristics. Accordingly, the work has been focused on hard discs for longitudinal recording and on protective and lubricating layers for use in Winchester drives. The new thin-film production technologies developed during these studies can now be used in a futureproduction line, based on the new equipment now available, with the quality and reproducibility needed to market the discs.
Wissenschaftliches Gebiet (EuroSciVoc)
CORDIS klassifiziert Projekte mit EuroSciVoc, einer mehrsprachigen Taxonomie der Wissenschaftsbereiche, durch einen halbautomatischen Prozess, der auf Verfahren der Verarbeitung natürlicher Sprache beruht. Siehe: Das European Science Vocabulary.
CORDIS klassifiziert Projekte mit EuroSciVoc, einer mehrsprachigen Taxonomie der Wissenschaftsbereiche, durch einen halbautomatischen Prozess, der auf Verfahren der Verarbeitung natürlicher Sprache beruht. Siehe: Das European Science Vocabulary.
- Naturwissenschaften Naturwissenschaften Plasmaphysik
- Technik und Technologie Werkstofftechnik Beschichtung
Sie müssen sich anmelden oder registrieren, um diese Funktion zu nutzen
Programm/Programme
Mehrjährige Finanzierungsprogramme, in denen die Prioritäten der EU für Forschung und Innovation festgelegt sind.
Mehrjährige Finanzierungsprogramme, in denen die Prioritäten der EU für Forschung und Innovation festgelegt sind.
Thema/Themen
Aufforderungen zur Einreichung von Vorschlägen sind nach Themen gegliedert. Ein Thema definiert einen bestimmten Bereich oder ein Gebiet, zu dem Vorschläge eingereicht werden können. Die Beschreibung eines Themas umfasst seinen spezifischen Umfang und die erwarteten Auswirkungen des finanzierten Projekts.
Daten nicht verfügbar
Aufforderungen zur Einreichung von Vorschlägen sind nach Themen gegliedert. Ein Thema definiert einen bestimmten Bereich oder ein Gebiet, zu dem Vorschläge eingereicht werden können. Die Beschreibung eines Themas umfasst seinen spezifischen Umfang und die erwarteten Auswirkungen des finanzierten Projekts.
Aufforderung zur Vorschlagseinreichung
Verfahren zur Aufforderung zur Einreichung von Projektvorschlägen mit dem Ziel, eine EU-Finanzierung zu erhalten.
Daten nicht verfügbar
Verfahren zur Aufforderung zur Einreichung von Projektvorschlägen mit dem Ziel, eine EU-Finanzierung zu erhalten.
Finanzierungsplan
Finanzierungsregelung (oder „Art der Maßnahme“) innerhalb eines Programms mit gemeinsamen Merkmalen. Sieht folgendes vor: den Umfang der finanzierten Maßnahmen, den Erstattungssatz, spezifische Bewertungskriterien für die Finanzierung und die Verwendung vereinfachter Kostenformen wie Pauschalbeträge.
Finanzierungsregelung (oder „Art der Maßnahme“) innerhalb eines Programms mit gemeinsamen Merkmalen. Sieht folgendes vor: den Umfang der finanzierten Maßnahmen, den Erstattungssatz, spezifische Bewertungskriterien für die Finanzierung und die Verwendung vereinfachter Kostenformen wie Pauschalbeträge.
Daten nicht verfügbar
Koordinator
8755 ALZENAU
Deutschland
Die Gesamtkosten, die dieser Organisation durch die Beteiligung am Projekt entstanden sind, einschließlich der direkten und indirekten Kosten. Dieser Betrag ist Teil des Gesamtbudgets des Projekts.