INfrared STRUctural monitoring of Cracks using Thermoelastic analysis In production enVironmEnts

Informazioni relative al progetto

INSTRUCTIVE

ID dell’accordo di sovvenzione: 686777

DOI

10.3030/686777

Progetto chiuso

Data della firma CE 3 Dicembre 2015

Data di avvio 1 Gennaio 2016

Data di completamento 31 Dicembre 2018

Finanziato da

• SOCIETAL CHALLENGES - Smart, Green And Integrated Transport

Costo totale

€ 386 062,50

Contributo UE

€ 349 558,88

Coordinato da

STRAIN SOLUTIONS LIMITED
United Kingdom

Periodic Reporting for period 2 - INSTRUCTIVE (INfrared STRUctural monitoring of Cracks using Thermoelastic analysis In production enVironmEnts)

Periodo di rendicontazione: 2017-07-01 al 2018-12-31

Sintesi del contesto e degli obiettivi generali del progetto

This project is built around a well-established set of laboratory-based techniques, which use Thermoelastic Stress Analysis (TSA) for characterising strain fields associated with structural features. The project extends their applicability to aircraft structure tests and to enhance their productivity through the use of automation for data acquisition and processing in an industrial environment. Thermoelastic stress analysis is well-established as a laboratory-based technique and its use for structural analysis, fracture mechanics and damage mechanics has been explored extensively. Most of the work so far has been performed using relatively small test coupons with simple structural features. In this project the aim was to prove the feasibility of applying thermoelastic stress analysis in a structural test environment for detecting stress hotspots. The structural test tools developed enable fast acquisition of data-rich stress fields in large aerospace components during structural tests at relatively low cost, and the post-processing capabilities allow meaningful comparison of experimental results with those from computational models and service life evaluations. The scientific and technical objectives led to innovative methodologies that enable more detailed stress information to be acquired during aircraft structure tests. These methodologies are faster, lower cost and provide higher confidence in computational models than was previously possible.

Overall project objectives:

(i) to develop methods and protocols for the application of thermoelastic stress analysis (TSA) to aircraft structure fatigue and damage tolerance tests;
(ii) to demonstrate the applicability of TSA for quantitative stress analysis of complex three dimensional components;
(iii) to evaluate TSA for qualitative and quantitative assessment of hot-spots during structural testing;
(iv) to design, build and demonstrate a robotic platform for TSA data acquisition in an industrial test environment;
(v) to propose an approach for the implementation of the technology on large components and full-scale tests with the provision of quantitative results.

Lavoro eseguito dall’inizio del progetto fino alla fine del periodo coperto dalla relazione e principali risultati finora ottenuti

A robust methodology of data collection using thermoelastic stress analysis (TSA) during constant amplitude cyclic loading of fatigue coupon specimens has been developed. Post-processing of the TSA signal magnitude data is carried out using an algorithm implemented in MATLAB. This method allows the time of crack initiation to be determined, and the propagation of those cracks to be tracked and measured. Results show that crack initiation is observed when cracks are at sub-millimetre lengths, and propagating cracks can be continuously tracked up to 10 mm in length.

Thermoelastic stress analysis has also been carried out on simple specimens with a primer paint coating, complex specimens under constant amplitude cyclic loading, and on simple specimens under spectrum (flight cycle) loading. Preliminary results show that TSA can be used to observe cracks in each of these complex situations before they would be apparent using traditional methods of non-destructive inspection.

A prototype electro-mechanical positioning rig for scanning of a component for hotspots or the presence of cracks has been developed which makes use of an Arduino control interface board connected to a laptop computer via USB connection, with the Arduino permitting the use of the laptop keyboard to control the movement of the rig. Control steps are executed both automatically and with user interaction, via both stepper motor and rotary servo actuators, and example translations and rotations are executed which will be suitable for infrared camera positioning.

Progressi oltre lo stato dell’arte e potenziale impatto previsto (incluso l’impatto socioeconomico e le implicazioni sociali più ampie del progetto fino ad ora)

Progress beyond the state of the art - the current project deliverables document a methodology for successful automated real-time tracking of crack growth in planar specimens under both cyclic and flight spectrum loading, which is a significant step forward in the current state of the art for non-contact crack monitoring methods.

Expected results until the end of the project - the methodology developed in this work include application to complex aerospace structural components, more advanced flight spectrum loading, non-planar components and low frequency excitation during fatigue loading. The project also considers scanning methodologies so that large areas of a component undergoing structural test may be monitored by a single thermoelastic stress analysis system.

Potential impact of the project so far - the methodologies developed in the project offer a complete methodology for continuous crack tip tracking data to be reported in real time during complex fatigue loading of components, removing the requirement for regular stops in fatigue test programmes for visual inspection of crack tip positions, which represents a significant, quantifiable cost saving for the end user and also an improvement in the crack length accuracy over traditional monitoring methods.