H2020-IBA-CS2-GAMS-2020-2021

Deliverables

Documents, reports (2)

D0.6 Dissemination and Communication Plan 2020

Update of the dissemination and communication plan for ENG-ITD

D0.5 DMP

Data Management Plan report

Publications

Conference proceedings (14)

In situ synchrotron X-ray imaging of titanium alloy powder sintering during directed energy deposition additive manufacturing

Author(s): Lorna Sinclair, Dr Yunhui Chen, Dr Samuel J. Clark, Sebastian Marussi, David T. Rees, Dr Gavin Baxter, Martyn Jones, Dr Robert Atwood, Dr Chu Lun Alex Leung, Prof. Iain Todd, Prof. Peter D. Lee
Published in: 2020

Experimental investigation of the aerodynamics of a 1.5 stage High-Speed Low-Pressure turbine

Author(s): Torre, A.
Published in: 2020

Study on Accuracy of Heat Transfer Coefficient Determination in the Bearing Chamber for Gas Turbine Engine

Author(s): Illia Petukhov, Taras Mykhailenko, Sergiy Yepifanov, Oleg Shevchuk
Published in: 2020

Purge and Leakage Flow Effects on the Aerodynamics of a High-Speed Low-Pressure Turbine Cascade

Author(s): Lopes, G.
Published in: 2020

Understanding Directed Energy Deposition Additive Manufacturing Process using In situ and Operando X-ray Imaging and Diffraction

Author(s): """Yunhui Chen, Samuel Clark, Sebastian Marussi, David Collins, Martyn Jones, Gavin Baxter, Thomas Connolley, Robert Atwood, Chu-Lun Alex Leung, Peter D. Lee"""
Published in: 2020

Capturing Pore Formation during Laser Blown Powder Directed Energy Deposition

Author(s): Peter D Lee, Yunhui Chen, Lorna Sinclair, CL Alex Leung, Sam Clark, Sebastian Marussi, Robert C. Atwood, Martyn A. Jones, Gavin J. Baxter
Published in: 2020

Purge and Leakage Flow Effects on the Aerodynamics of a High-Speed Low-Pressure Turbine Cascade

Author(s): Lopes, G., Lavagnoli, S., Gendebien, S., Hillewaert, K.
Published in: 2020

NUMERICAL OPTIMIZATION OF LINER IMPEDANCE IN ACOUSTIC DUCT

Author(s): Kevin Billon, Emanuele de Bono, Matthias Perez, Edouard Salze, Gael Matten, Morvan Ouisse, Maxime Volery, Herve Lissek, Jacky Mardjono
Published in: 2020

Benefit of mesh adaption vs. conventional CFD approach for nacelle aerodynamics with ground effect

Author(s): G.Millot, S.Raynal and A.Laurencin
Published in: 2020

Overview of joint ITP Aero and University research

Author(s): A. López, N. López
Published in: 2020

DESIGN AND OPTIMIZATION OF PIEZOELECTRIC ACTUATORS FOR AEROACOUSTIC NOISES CONTROL IN A TURBOFAN

Author(s): M. Perez, M. Ezzine, K. Billon, V. Clair, J. Marjono, and M. Collet
Published in: 2020

Design and Testing of a Multi-Stage IP Turbine for Future Geared Turbofans

Author(s): D. Torre, G. García-Valdecasas, A. Puente, D. Hernández, S. Luque, P. Benito
Published in: 2021

Quantification for Directed Energy Deposition Additive Manufacturing Process using In situ and Operando X-ray Imaging

Author(s): Yunhui Chen, Samuel Clark, Lorna Sinclair, Chu-Lun Alex Leung, Sebastian Marussi, Martyn Jones, Gavin Baxter, Thomas Connolley, Robert Atwood, Graham McCartney, Iain Todd, Peter D. Lee
Published in: 2020

Experimental investigation of the aerodynamics of a 1.5 stage High-Speed Low-Pressure turbine

Author(s): Torre, A., Lavagnoli, S., Gendebien, S., Hillewaert, K.
Published in: 2020

Peer reviewed articles (5)

Correlative Synchrotron X-ray Imaging and Diffraction of Directed Energy Deposition Additive Manufacturing

Author(s): Yunhui Chen, Samuel J. Clark, David M. Collins, Sebastian Marussi, Simon A. Hunt, Danielle M. Fenech, Thomas Connolley, Robert C. Atwood, Oxana V. Magdysyuk, Gavin J. Baxter, Martyn A. Jones, Chu Lun Alex Leung, Peter D. Lee
Published in: Acta Materialia, Issue 209, 2021, Page(s) 116777, ISSN 1359-6454
DOI: 10.1016/j.actamat.2021.116777

LARGE-EDDY SIMULATION OF A MODEL AERO-ENGINE SOOTING FLAME WITH A MULTIPHYSICS APPROACH

Author(s): S. Paccati, D. Bertini, L. Mazzei, A. Andreini and S. Puggelli
Published in: Flow Turbulence Combust, 2020, ISSN 1573-1987
DOI: 10.1007/s10494-020-00202-5

Modeling of Partially Wetting Liquid Film Using an Enhanced Thin Film Model for Aero-Engine Bearing Chamber Applications

Author(s): Kuldeep Singh, Medhat Sharabi, Richard Jefferson-Loveday, Stephen Ambrose, Carol Eastwick, Jing Cao, Adrian Jacobs
Published in: Journal of Engineering for Gas Turbines and Power, Issue 143/4, 2021, ISSN 0742-4795
DOI: 10.1115/1.4049663

Melt pool morphology in directed energy deposition additive manufacturing process

Author(s): Y Chen, S Clark, A C L Leung, L Sinclair, S Marussi, R Atwood, T Connoley, M Jones, G Baxter, P D Lee
Published in: IOP Conference Series: Materials Science and Engineering, Issue 861, 2020, Page(s) 012012, ISSN 1757-899X
DOI: 10.1088/1757-899x/861/1/012012

In situ X-ray quantification of melt pool behaviour during directed energy deposition additive manufacturing of stainless steel

Author(s): Yunhui Chen, Samuel J. Clark, Yuze Huang, Lorna Sinclair, Chu Lun Alex Leung, Sebastian Marussi, Thomas Connolley, Oxana V. Magdysyuk, Robert C. Atwood, Gavin J. Baxter, Martyn A. Jones, Iain Todd, Peter D. Lee
Published in: Materials Letters, Issue 286, 2021, Page(s) 129205, ISSN 0167-577X
DOI: 10.1016/j.matlet.2020.129205

Thesis dissertations (1)

Methodology of support modeling for additive process simulation

Author(s): T. Laudadio
Published in: 2020