Obiettivo
To demonstrate that a fluidized bed combustion plant can burn acid tars and waste oils without additional energy in a manner which absolutely avoids environmental pollution and generates process steam using the hot waste gas.
The plant was in operation for more than 7 000 hours up to the end of the project. It was successfully tested and, for the most part, found to be operationally safe. In the course of this demonstration period acid tars (calorific value approximately 18 600 KJ/Kg) and waste oils (calorific value approximately 27 900 KJ/Kg) were burned and simultaneously steam was produced for the process. The design data of the plant were attained after optimization. The throughput capacity is given as 2.5 T/H creosote or waste oil. The steam generating capacity amounts to 3.5 T/H at 11 Bar in the rated load point. The bed temperature is around 800 deg. C. and the combustion chamber temperature around 700 deg.C. Combustion takes place at an excess air ratio of approximately 20%. The thermal efficiencies reached values of between 78% and 86% depending on the waste material used. The start-up to full load time is 4 hours from a cold condition and 2 hours after week-end shutdown. Start-up is effectedvia 2 oil or gas-fired start up burners. The emission values were either met or were below the emission standards specified by the UK authorities (particulates lead SO3 SO2 plume value).Deborah,established in 1975, is the only company to design and develop a fluidised bed boiler, which combusts acid tar waste as its fuel. This boiler (installed at Tenneco Chemicals, Avonmouth) is the result of many years research, is unique in design, and exclusive to Deborah. The same combustion technology can be applied to the efficient, clean combustion of coal, oil and gas.
A prototype plant with a power of 4 MW was erected and tested on the premises of Tenneco Organics Ltd in Avonmouth. The plant is a process steam plant equipped with a fluidized bed combustion facility for the combustion of residual waste from the processing of used oil in which all fuel engineering and thermal aspects are suited to each other. The patented circulating fluidized bed process should eliminate the disadvantages of conventional or vertical fluidized bed systems and lead to the total combustion of residual waste with low calorific values too. The bed material gases and feedstock circulate in a controlled manner in the fluidized bed on a roughly eliptical path. As a result of the horizontal and vertical turbulances intensive mixing takes place and there is a relatively uniform distribution in the fluidized bed. A membrane wall boiler with overhead header is used as steam generator. This membrane wall boiler is in direct contact with the approximately 800 deg. C. hot fluidized bed in the main combustion chamber. The flue gases are cooled down to a temperature of about 300 deg. C. in a further step. The plant is equipped with a multi-cell cyclone to meet the specified limit values for the fine dust in the waste gas. Following erection the efficiency of the plant is to be examined and demonstrated over a longer operating period.
Campo scientifico (EuroSciVoc)
CORDIS classifica i progetti con EuroSciVoc, una tassonomia multilingue dei campi scientifici, attraverso un processo semi-automatico basato su tecniche NLP. Cfr.: Il Vocabolario Scientifico Europeo.
CORDIS classifica i progetti con EuroSciVoc, una tassonomia multilingue dei campi scientifici, attraverso un processo semi-automatico basato su tecniche NLP. Cfr.: Il Vocabolario Scientifico Europeo.
Questo progetto non è ancora stato classificato con EuroSciVoc.
Suggerisci i campi scientifici che ritieni più rilevanti e aiutaci a migliorare il nostro servizio di classificazione.
È necessario effettuare l’accesso o registrarsi per utilizzare questa funzione
Programma(i)
Programmi di finanziamento pluriennali che definiscono le priorità dell’UE in materia di ricerca e innovazione.
Programmi di finanziamento pluriennali che definiscono le priorità dell’UE in materia di ricerca e innovazione.
Argomento(i)
Gli inviti a presentare proposte sono suddivisi per argomenti. Un argomento definisce un’area o un tema specifico per il quale i candidati possono presentare proposte. La descrizione di un argomento comprende il suo ambito specifico e l’impatto previsto del progetto finanziato.
Gli inviti a presentare proposte sono suddivisi per argomenti. Un argomento definisce un’area o un tema specifico per il quale i candidati possono presentare proposte. La descrizione di un argomento comprende il suo ambito specifico e l’impatto previsto del progetto finanziato.
Invito a presentare proposte
Procedura per invitare i candidati a presentare proposte di progetti, con l’obiettivo di ricevere finanziamenti dall’UE.
Dati non disponibili
Procedura per invitare i candidati a presentare proposte di progetti, con l’obiettivo di ricevere finanziamenti dall’UE.
Meccanismo di finanziamento
Meccanismo di finanziamento (o «Tipo di azione») all’interno di un programma con caratteristiche comuni. Specifica: l’ambito di ciò che viene finanziato; il tasso di rimborso; i criteri di valutazione specifici per qualificarsi per il finanziamento; l’uso di forme semplificate di costi come gli importi forfettari.
Meccanismo di finanziamento (o «Tipo di azione») all’interno di un programma con caratteristiche comuni. Specifica: l’ambito di ciò che viene finanziato; il tasso di rimborso; i criteri di valutazione specifici per qualificarsi per il finanziamento; l’uso di forme semplificate di costi come gli importi forfettari.
Coordinatore
MIDDLESBROUGH
Regno Unito
I costi totali sostenuti dall’organizzazione per partecipare al progetto, compresi i costi diretti e indiretti. Questo importo è un sottoinsieme del bilancio complessivo del progetto.