Ziel
Evaluation of the potential of different deposition techniques with regard to reproducibility and robustness for future production of high-efficiency CdTe thin film solar cells.
The main advantage of catalytic combustion is the low thermal nitrogen oxides emission due to the low operating temperature. Many tests have been performed successfully with clean fuels, and a hybrid catalytic and staged combustion technique is also able to burn fuels containing high amounts of nitrogen with low nitrogen oxides emission levels and a combustion efficiency comparable to conventional burners.
In gas turbine applications, a catalytic combustor can lower emissions of nitrogen oxides to less than about 2 parts per million. Catalytic combustion can also burn mixtures whose combustible concentration is below the lean mixture limit of gas phase reactions. This feature leads to an easier control of the rate of production of thermal energy.
Considerable improvements are required before these techniques can be considered for large scale applications including:
reduction of methane losses;
development of cheap and thermostable combustion catalysts;
increasing the temperature stability of the catalysts;
improvement of the fuel preparation and injection systems.
An evaluation has been made of the potential of different deposition techniques with regard to reproducibility and robustness for future production of high efficiency cadmium tellurium thin film solar cells.
The eventual production of a cadmium tellurium thin film solar cell can only be envisaged, if materials and production techniques are cheap enough. This means that the use of the semiconductor material must be made efficient by using thin films and efficient deposition technologies and cheap substrates. Past work and evaluations have shown that this is possible. More of a question arises with respect to deposition technology. Here, a robust process will be required, which leads to a high production efficiency under not too stringent (and thereby expensive) process control. The control bandwidth of all essential parameters for reliable production of high efficiency solar cells should be as wide as possible.
Research so far has resulted in an efficiency of 12% in a cadmium tellurium cadmium selenium CdTe-CdSe heterojunction cell. This process uses cheaper material and is more suitable for mass production and is within the economic limits. Safety aspects can be resolved and the set up of a production plant is under discussion.
The eventual production of a CdTe thin film solar cell can only be envisaged, if materials and production techniques are cheap enough for realization of the final aim of <<1ECU/Wp. This means, that the use of the semiconductor material is made materials' efficient by using thin films and materials' efficient deposition technologies and cheap substrates. Past work and evaluations have shown that this is possible. More of a question arises within the scope of deposition technology. Here, a robust process will be required, which leads to a high production efficiency under not too stringent - and thereby expensive - process control. The control bandwidth of all essential parameters for reliable production of high-efficiency solar cells should be as wide as possible.
This latter technological aspect, besides special development work, such as improving doping and contacting of CdTe, is the central focus of the proposed joint effort. A close cooperation and evaluation of results therefore is essential for the expected success of the work.
In the following the tasks of the individual research groups are listed:
Task 1) COORDINATION AND EVALUATION (Battelle Institut e.V.)
Task 2) CLOSE-SPACED SUBLIMATION (Battelle Institut e.V.) not financed by the EC
Task 3) HIGH VACUUM EVAPORATION AND GALVANIC DEPOSITION (Newcastle- upon-Tyne polytechnic)
Task 4) DOPING AND CONTACTING OF CdTe BY ION-ASSISTED TECHNOLOGY (Istituto Nazionale di Fisica Nucleare)
Task 5) METALORGANIC CHEMICAL VAPOUR DEPOSITION (University of Durham)
Task 6) SCREEN PRINTING OF CdTe (University of Ghent)
Wissenschaftliches Gebiet (EuroSciVoc)
CORDIS klassifiziert Projekte mit EuroSciVoc, einer mehrsprachigen Taxonomie der Wissenschaftsbereiche, durch einen halbautomatischen Prozess, der auf Verfahren der Verarbeitung natürlicher Sprache beruht. Siehe: Das European Science Vocabulary.
CORDIS klassifiziert Projekte mit EuroSciVoc, einer mehrsprachigen Taxonomie der Wissenschaftsbereiche, durch einen halbautomatischen Prozess, der auf Verfahren der Verarbeitung natürlicher Sprache beruht. Siehe: Das European Science Vocabulary.
- Naturwissenschaften Chemiewissenschaften anorganische Chemie Übergangsmetalle
- Technik und Technologie Werkstofftechnik Beschichtung
- Sozialwissenschaften Wirtschaftswissenschaften Wirtschaftswissenschaft Produktionswirtschaft
- Technik und Technologie Umwelttechnik Energie und Kraftstoffe
- Naturwissenschaften Chemiewissenschaften anorganische Chemie Metalloide
Sie müssen sich anmelden oder registrieren, um diese Funktion zu nutzen
Programm/Programme
Mehrjährige Finanzierungsprogramme, in denen die Prioritäten der EU für Forschung und Innovation festgelegt sind.
Mehrjährige Finanzierungsprogramme, in denen die Prioritäten der EU für Forschung und Innovation festgelegt sind.
Thema/Themen
Aufforderungen zur Einreichung von Vorschlägen sind nach Themen gegliedert. Ein Thema definiert einen bestimmten Bereich oder ein Gebiet, zu dem Vorschläge eingereicht werden können. Die Beschreibung eines Themas umfasst seinen spezifischen Umfang und die erwarteten Auswirkungen des finanzierten Projekts.
Daten nicht verfügbar
Aufforderungen zur Einreichung von Vorschlägen sind nach Themen gegliedert. Ein Thema definiert einen bestimmten Bereich oder ein Gebiet, zu dem Vorschläge eingereicht werden können. Die Beschreibung eines Themas umfasst seinen spezifischen Umfang und die erwarteten Auswirkungen des finanzierten Projekts.
Aufforderung zur Vorschlagseinreichung
Verfahren zur Aufforderung zur Einreichung von Projektvorschlägen mit dem Ziel, eine EU-Finanzierung zu erhalten.
Daten nicht verfügbar
Verfahren zur Aufforderung zur Einreichung von Projektvorschlägen mit dem Ziel, eine EU-Finanzierung zu erhalten.
Finanzierungsplan
Finanzierungsregelung (oder „Art der Maßnahme“) innerhalb eines Programms mit gemeinsamen Merkmalen. Sieht folgendes vor: den Umfang der finanzierten Maßnahmen, den Erstattungssatz, spezifische Bewertungskriterien für die Finanzierung und die Verwendung vereinfachter Kostenformen wie Pauschalbeträge.
Finanzierungsregelung (oder „Art der Maßnahme“) innerhalb eines Programms mit gemeinsamen Merkmalen. Sieht folgendes vor: den Umfang der finanzierten Maßnahmen, den Erstattungssatz, spezifische Bewertungskriterien für die Finanzierung und die Verwendung vereinfachter Kostenformen wie Pauschalbeträge.
Koordinator
NE1 7RU Newcastle upon Tyne
Vereinigtes Königreich
Die Gesamtkosten, die dieser Organisation durch die Beteiligung am Projekt entstanden sind, einschließlich der direkten und indirekten Kosten. Dieser Betrag ist Teil des Gesamtbudgets des Projekts.