Skip to main content
Przejdź do strony domowej Komisji Europejskiej (odnośnik otworzy się w nowym oknie)
polski pl
CORDIS - Wyniki badań wspieranych przez UE
CORDIS

Tomorrow’s mobility solutions, today

Opis projektu

Drukowanie indywidualnie dopasowanych lejów protetycznych

Obecnie niemal każda osoba po amputacji kończyny dolnej korzysta ze standardowych lejów protetycznych, stanowiących warstwę wytłumiającą pomiędzy kończyną a gniazdem protezy. Takie leje o standardowym kształcie mogą jednak powodować ból podczas chodzenia. Leje wykonywane na miarę są lepsze, ale droższe. Brakuje skutecznego rozwiązania umożliwiającego wytwarzanie lejów dopasowanych do kształtu ciała danej osoby po amputacji. W tym kontekście zespół finansowanego przez UE projektu MotionTech wykorzysta postępy w zakresie technologii 3D, aby umożliwić skanowanie 3D kończyn i wytwarzanie indywidualnie dopasowanych lejów drukowanych w technologii druku przestrzennego. Zespół MotionTech zbierze informacje potrzebne do udoskonalenia produktu, aby wprowadzić na rynek nowe leje protetyczne.

Cel

Today, around 90% of patients living with lower limb amputation do not have tailored liners and need to resort to standard–shape prosthetic liners due to cost and technology limitations. However, that causes them discomfort and pain whilst they walk. Worse, despite extensive science providing evidence of the advantages of customizing the local hardness of the prosthetic liner to the underlying tissues of the patients (e.g. increased comfort & overall mobility, etc.), there is no viable solution to provide adapted multi-hardness prosthetic liners to amputated patients.
In response, MotionTech offers 3D scanning and delivers 3D printed tailored liners with a novel service model based on POC 3D scanning that allows us to deliver tailored multi-hardness liners to O&P (orthotic & prosthetic) centres within 48 hours (at €850 for new and €700 for renewal liners).
We are seizing the advances in 3D technology, the need for prosthetics due to the ageing society and cost pressure on healthcare providers. This allows us to tap into an addressable market of €75M in the EU and €60M in the US, conservatively assuming that only 25% of amputees will receive tailored liners, which is close to €150M addressable market.
Swiss Motion Technologies SA was created in late 2016 by Kevin Mamalis, an electro-mechanical engineer specialised in additive manufacturing technologies. He was joined by two further co-founders. The Phase 1 funding will help us gather the necessary insights for a Phase 2 product improvement project after which we can enter the market.
We therefore aim to give birth to an impactful technology for orthopaedic patients that is based on 3D scanning, 3D printing and a software suite that replace inaccurate manual measurements and liners.

Dziedzina nauki (EuroSciVoc)

Program(-y)

Temat(-y)

System finansowania

SME-1 - SME instrument phase 1

Wyświetl wszystkie projekty finansowane w ramach tego programu finansowania

Zaproszenie do składania wniosków

(odnośnik otworzy się w nowym oknie) H2020-EIC-SMEInst-2018-2020

Wyświetl wszystkie projekty finansowane w ramach tego zaproszenia

Koordynator

SWISS MOTION TECHNOLOGIES SA
Wkład UE netto
€ 50 000,00
Adres
PLACE DE LA GARE 4
1020 RENENS
Szwajcaria
MŚP
Tak
Region
Schweiz/Suisse/Svizzera Région lémanique Vaud
Rodzaj działalności
Private for-profit entities (excluding Higher or Secondary Education Establishments)
Linki
Koszt całkowity
€ 71 429,00