Rezultaty
Metallic textured surfaces will be developed with chemical etching techniques. This is the intermediate version of the final Deliverable D1.2.
Fabrication (polymeric interfaces)A thick (>300 nm) polymeric coating will be deposited on a flat metal surface with spray. After the deposition, a plasma nanotexturing step followed by a plasma deposition step of a hydrophobic coating will be performed to create the desired morphology on the condenser.
Fabrication (composite interfaces) - finalHydrophobic polymer binder matrices will be filled with 2D thermally conductive materials such as graphene, MoS2 along with ultra-long carbon nanotubes. This is the final version of the intermediate Deliverable D1.3.
Setup for distillation experiments intermediate - intermediateA setup will be developed by MPIP which will evaluate the membrane distillation efficiency and dynamics of all developed surfaces. This is the intermediate version of the final Deliverable D3.4.
Setup for distillation experiments - finalA setup will be developed by MPIP which will evaluate the membrane distillation efficiency and dynamics of all developed surfacesThis is the final version of the final Deliverable D33
Fabrication (composite interfaces) - intermediateHydrophobic polymer binder matrices will be filled with 2D thermally conductive materials such as graphene, MoS2 along with ultra-long carbon nanotubes. This is the intermediate version of the final Deliverable D1.2.
Heat transfer and robustnessThe best candidate heat transfer materials will be screened via performing durability and aging tests
Fabrication (metallic textures) - finalMetallic textured surfaces will be developed with chemical etching techniques. This is the final version of the interim Deliverable D1.1
Fabrication (chemical coating)A superhydrophobic chemical coating will be applied in the internal part of capillaries by flow-through methods. Solution processed particle suspensions and MOF dispersions will be employed for this flow-through coating approach.
Enhanced heat transferThe heat transfer performance of all the developed materials for dropwise condensation will be evaluated in custom condensation setups.
Documents for Reviewers
Design of measurement protocolPrevious analytical models, simulation studies and experimental work will be used by all partners to define preliminary design rules for optimal submicron hierarchical morphologies needed for each application.
Validated framework for DWCA modelling framework previously used for studying wetting transitions without phase-change will be suitably modified. The shape of the droplet during DWC and the pertinent heat flux to the solid substrate will be calculated.
7 high impact factor papers concerning the different topics of the project will be published
For the scientific community the dissemination will include the organization of at least one and preferably two workshops in international conferences related to the project activities
Patent applicationsBefore dissemination of the project results those of commercial merit will be protected This will be done through patents filed by partners in their country and to EPO with priority from their country filing within the life of this project At least one but most probably several patents are targeted
Web page and logo establishedThe web page and the logo will be established.
Publikacje
Autorzy:
Ultrathin Durable Organic Hydrophobic Coatings Enhancing Dropwise Condensation Heat Transfer
Opublikowane w:
Langmuir, 2022, ISSN 0743-7463
Wydawca:
American Chemical Society
DOI:
10.1021/acs.langmuir.2c01477
Autorzy:
Matteo Donati, Cheuk Wing Edmond Lam, Athanasios Milionis, Chander Shekhar Sharma, Abinash Tripathy, Armend Zendeli, Dimos Poulikakos
Opublikowane w:
Advanced Materials Interfaces, 2020, Strona(/y) 2001176, ISSN 2196-7350
Wydawca:
Wiley‐VCH GmbH
DOI:
10.1002/admi.202001176
Autorzy:
Maria Tzianou, Giannis Thomopoulos, Nikolaos Vourdas, Kosmas Ellinas, Evangelos Gogolides
Opublikowane w:
Advanced Functional Materials, 2020, Strona(/y) 2006687, ISSN 1616-301X
Wydawca:
John Wiley & Sons Ltd.
DOI:
10.1002/adfm.202006687
Autorzy:
A.Arapis,
V.Constantoudis,
D.Kontziampasisc,
A.Milionis,
C.W.E.Lam,
A.Tripathy,
D.Poulikakos,
E.Gogolides
Opublikowane w:
Materials today: proceedings, 2021, ISSN 2214-7853
Wydawca:
Elsevier
DOI:
10.1016/j.matpr.2021.10.120
Autorzy:
Amirreza Shayganpour, Marialaura Clausi, and Ilker S. Bayer
Opublikowane w:
Appl. Phys. Lett. 118, Numer Vol.118, Numer 9, 2021, ISSN 0003-6951
Wydawca:
American Institute of Physics
DOI:
10.1063/5.0042404
Autorzy:
V. Constantoudis, I. Ioannou-Sougleridis, A. Dimou, A. Ninou, M. Chatzichristidi, E. Makarona
Opublikowane w:
Micro and Nano Engineering, Numer Voume 16, 2022, ISSN 2590-0072
Wydawca:
Elsevier
DOI:
10.1016/j.mne.2022.100148
Autorzy:
Abinash Tripathy, Cheuk Wing Edmond Lam, Diana Davila, Matteo Donati, Athanasios Milionis, Chander Shekhar Sharma, Dimos Poulikakos
Opublikowane w:
ACS Nano, 2021, ISSN 1936-0851
Wydawca:
American Chemical Society
DOI:
10.1021/acsnano.1c02932
Autorzy:
George Memos, George Kokkoris, Vassilios Constantoudis, Cheuk Wing Edmond Lam, Abinash Tripathy, Efstratios Mitridis, Athanasios Milionis, Dimos Poulikakos, Evangelos Gogolides
Opublikowane w:
International Journal of Heat and Mass Transfer, Numer Volume 197, 2022, 123297,, 2022, ISSN 0017-9310
Wydawca:
Pergamon Press Ltd.
DOI:
10.1016/j.ijheatmasstransfer.2022.123297
Autorzy:
Vikramjeet Singh, Xuehu Men, and Manish K. Tiwari
Opublikowane w:
Nano Letters, 2021, ISSN 1530-6984
Wydawca:
American Chemical Society
DOI:
10.1021/acs.nanolett.1c00157
Autorzy:
Panagiotis Sarkiris, Kosmas Ellinas, Dimitris Gkiolas, Dimitrios Mathioulakis, Evangelos Gogolides
Opublikowane w:
Advanced Functional Materials, 2019, Strona(/y) 1902905, ISSN 1616-301X
Wydawca:
John Wiley & Sons Ltd.
DOI:
10.1002/adfm.201902905
Autorzy:
Chander Shekhar Sharma, Cheuk Wing Edmond Lam, Athanasios Milionis, Hadi Eghlidi, Dimos Poulikakos
Opublikowane w:
ACS Applied Materials & Interfaces, Numer 11/30, 2019, Strona(/y) 27435-27442, ISSN 1944-8244
Wydawca:
American Chemical Society
DOI:
10.1021/acsami.9b07673
Autorzy:
Zhe Li, Athanasios Milionis, Yu Zheng, Marcus Yee, Lukas Codispoti, Freddie Tan, Dimos Poulikakos, Choon Hwai Yap
Opublikowane w:
Nature Communications, Numer 10/1, 2019, ISSN 2041-1723
Wydawca:
Nature Publishing Group
DOI:
10.1038/s41467-019-13512-8
Autorzy:
Marialaura Clausi, Silvia Grasselli, Annalisa Malchiodi, Ilker S. Bayer
Opublikowane w:
Applied Surface Science, Numer 529, 2020, Strona(/y) 147070, ISSN 0169-4332
Wydawca:
Elsevier BV
DOI:
10.1016/j.apsusc.2020.147070
Autorzy:
Athanasios Milionis, Abinash Tripathy, Matteo Donati, Chander Shekhar Sharma, Fei Pan, Katharina Maniura-Weber, Qun Ren, Dimos Poulikakos
Opublikowane w:
Industrial & Engineering Chemistry Research, 2020, ISSN 0888-5885
Wydawca:
American Chemical Society
DOI:
10.1021/acs.iecr.0c01998
Autorzy:
Christos Stamatopoulos, Athanasios Milionis, Norbert Ackerl, Matteo Donati, Paul Leudet de la Vallée, Philipp Rudolf von Rohr, Dimos Poulikakos
Opublikowane w:
ACS Nano, 2020, ISSN 1936-0851
Wydawca:
American Chemical Society
DOI:
10.1021/acsnano.0c03849
Autorzy:
Marialaura Clausi, Muhammad Zahid, Amirreza Shayganpour, Ilker S. Bayer
Opublikowane w:
Advanced Composites and Hybrid Materials, 2022, ISSN 2522-0128
Wydawca:
Springer
DOI:
10.1007/s42114-022-00426-1
Autorzy:
Marialaura Clausi, Ilker S. Bayer
Opublikowane w:
Nano Select, 2020, ISSN 2688-4011
Wydawca:
Wiley
DOI:
10.1002/nano.202000152
Autorzy:
Dimitrios Nioras, Kosmas Ellinas, Vassilios Constantoudis, Evangelos Gogolides
Opublikowane w:
ACS Applied Materials & Interfaces, 2021, ISSN 1944-8244
Wydawca:
American Chemical Society
DOI:
10.1021/acsami.1c16609
Autorzy:
Chander Shekhar Sharma,Athanasios Milionis,Abhinav Naga,Cheuk Wing Edmond Lam,Gabriel Rodriguez,Marco Francesco Del Ponte,Valentina Negri,Hopf Raoul,Maria D'Acunzi,Hans-Jürgen Butt,Doris Vollmer,Dimos Poulikakos
Opublikowane w:
Advanced Functional Materials, 2021, ISSN 1616-3028
Wydawca:
Willey
DOI:
10.1002/adfm.202109633
Wyszukiwanie danych OpenAIRE...
Podczas wyszukiwania danych OpenAIRE wystąpił błąd
Brak wyników